Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P019515    Engine Oil Temperature Sensor Circuit Short to Battery or Open

for Preparation Click here


DESCRIPTION

Refer to DTC P019511 .

DTC No.
DTC Detection Condition
Trouble Area
P019515
The engine oil temperature sensor output voltage is higher than 4.93 V for 5 seconds or more (1 trip detection logic).
  1. Open or short in engine oil temperature sensor circuit
  2. Engine oil temperature sensor
  3. ECM

HINT:
When this DTC is output, check the engine oil temperature in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Oil Temperature Sensor.

DTC No.
Engine Oil Temperature Sensor
Malfunction
P019515
-40°C (-40°F)
  1. Short to +B in THEO circuit
  2. Open in THEO circuit
  3. Open in ETHE circuit
If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the engine oil temperature sensor and uses the sensor voltage to calculate the engine oil temperature. If the engine oil temperature sensor output voltage deviates from the normal operating range, the ECM determines that the engine oil temperature sensor circuit is malfunctioning and stores a DTC.
  1. Example:
    1. If the engine oil temperature sensor output voltage is higher than 4.93 V for 5 seconds or more, the ECM store this DTC.

MONITOR STRATEGY


Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on.
  6. Start the engine and wait for the time indicated below.
    1. If the engine oil temperature sensor is higher than -10°C (14°F): 15 seconds or more.
    2. If the engine oil temperature sensor is -10°C (14°F) or less: 13 minutes or more.
  7. Enter the following menus: Powertrain / Engine / Trouble Codes.
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  10. Input the DTC: P019515.
  11. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P019511 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)


  1. Disconnect the engine oil temperature sensor connector.


    A339345E01


    Text in Illustration 
    *1
    Engine Oil Temperature Sensor
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Engine Oil Temperature Sensor)
    -
    -

  1. Connect terminals 1 (THEO) and 2 (E2) of the engine oil temperature sensor connector on the wire harness side.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Oil Temperature Sensor.

  1. Read the value displayed on the GTS.

    Standard Value:
    164°C (327°F) or higher



NG
Go to step 2
OK

REPLACE ENGINE OIL TEMPERATURE SENSOR (Click here)  

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL TEMPERATURE SENSOR - ECM)
  1. Disconnect the engine oil temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E102-1 (THEO) - E96-97 (THEO)
    Always
    Below 1 Ω
    E102-2 (E2) - E96-96 (ETHE)
    Always
    Below 1 Ω
    E102-1 (THEO) or E96-97 (THEO) - Other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)