Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P044313    Evaporative Emission System Purge Control Valve "A" Circuit Open

for Preparation Click here


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signals to the purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No.
DTC Detection Condition
Trouble Area
P044313
Both of the following conditions (a) and (b) are met (1 trip detection logic):
(a) The purge VSV operation duty signal is 5 to 95%.
(b) The target control value and actual control value do not match for 10 seconds or more.
  1. Open or short in purge VSV circuit
  2. Purge VSV
  3. No. 1 integration relay
  4. ECM

CONFIRMATION DRIVING PATTERN


A179391E12

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on.
  6. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

    HINT:
    The A/C switch and all accessory switches should be off.

  7. Idle the engine for 15 minutes or more [B].

    HINT:
    Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.

  8. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P044313.
  12. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].

  13. Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Enter the following menus: Powertrain / Engine / Trouble Codes [E].
  15. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  17. Input the DTC: P044313.
  18. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM


A338260E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following procedure.

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EVAP PURGE VSV)


    A235652E02
  1. Connect the GTS to the DLC3.
    Text in Illustration 
    *a
    VSV is on
    *b
    VSV is off

  1. Disconnect the fuel vapor feed hose (on the canister side) from the purge VSV.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

  1. When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction to your finger.

    OK:

    GTS Operation
    Specified Condition
    ON
    Purge VSV port applies suction to finger
    OFF
    Purge VSV port applies no suction to finger

    HINT:
    Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT PURGE VSV
  1. Inspect the purge VSV (Click here).



NG
REPLACE PURGE VSV (Click here)
OK


3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)


    A346302E01
  1. Disconnect the purge VSV connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Purge VSV)

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E49-1 - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
  1. Disconnect the purge VSV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E49-2 - E96-70 (PRG)
    Always
    Below 1 Ω
    E49-2 or E96-70 (PRG) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - PURGE VSV)
  1. Disconnect the purge VSV connector.

  1. Disconnect the No. 1 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1A-8 - E49-1
    Always
    Below 1 Ω
    1A-8 or E49-1 - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)