Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > MIL Circuit

for Preparation Click here


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the engine switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.
The MIL operation can be checked visually: When the engine switch is turned on (IG), the MIL should be illuminated and should turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM


A343250E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.

1.CHECK THAT MIL IS ILLUMINATED
  1. Perform troubleshooting in accordance with the table below.

    Result:

    Result
    Proceed to
    MIL remains ON
    A
    MIL does not illuminate
    B



B
Go to step 5
A


2.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Check if any DTCs have been detected. Note down any DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTCs are output
    B

    HINT:
    Check for detected DTCs output from other ECUs which relate to the MIL.



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
A


3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)


    A338714E01
  1. Disconnect the A84 ECM connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

  1. Turn the engine switch on (IG).

  1. Check that the MIL is not illuminated.

    OK:
    MIL is not illuminated.



NG
Go to step 4
OK

REPLACE ECM (Click here)  

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
  1. Disconnect the combination meter assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A84-27 (W) or I17-12 (CHK) - Body ground or other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.CHECK THAT MIL IS ILLUMINATED
  1. Check if the MIL is illuminated when the engine switch is turned on (IG).

    OK:
    MIL should be illuminated.



NG
Go to step 6
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

6.CHECK THAT ENGINE STARTS
  1. Turn the engine switch on (IG).

  1. Start the engine.

    Result:

    Result
    Proceed to
    Engine starts
    A
    Engine does not start*
    B

    HINT:
    *: The GTS cannot communicate with the ECM.



B
GO TO VC OUTPUT CIRCUIT (Click here)
A


7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
  1. Disconnect the combination meter assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A84-27 (W) - I17-12 (CHK)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)