SFI SYSTEM > VC Output Circuit |



| 1.CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when the engine switch is turned on (IG).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION BETWEEN GTS AND ECM |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
| Result | Proceed to |
| Communication is not possible | A |
| Communication is possible | B |
|
| ||||
| A | |
| 3.CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle body with motor assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 4.CHECK MIL (ACCELERATOR PEDAL SENSOR) |
Disconnect the accelerator pedal sensor assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 5.CHECK MIL (CRANKSHAFT POSITION SENSOR) |
Disconnect the crankshaft position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 6.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)) |
Disconnect the camshaft position sensor (for intake camshaft) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 7.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)) |
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 8.CHECK MIL (MASS AIR FLOW METER SUB-ASSEMBLY) |
Disconnect the mass air flow meter sub-assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 9.CHECK MIL (FUEL PRESSURE SENSOR) |
Disconnect the fuel pressure sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 10.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR) |
Disconnect the manifold absolute pressure sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 11.CHECK MIL (OIL PRESSURE SENDER GAUGE ASSEMBLY) |
Disconnect the oil pressure sender gauge assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 12.CHECK HARNESS AND CONNECTOR |
Disconnect the throttle body with motor assembly connector.
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the crankshaft position sensor connector.
Disconnect the camshaft position sensor (for intake camshaft) connector.
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the fuel pressure sensor connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the oil pressure sender gauge assembly connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E96-121 (VCTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A84-49 (VCPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A84-52 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| E96-110 (VCNE) - Body ground and other terminals | Always | 10 kΩ or higher |
| E96-113 (VCV1) - Body ground and other terminals | Always | 10 kΩ or higher |
| E96-111 (VCE1) - Body ground and other terminals | Always | 10 kΩ or higher |
| E96-90 (VCVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| E96-138 (VCPM) - Body ground and other terminals | Always | 10 kΩ or higher |
| E96-136 (VCPR) - Body ground and other terminals | Always | 10 kΩ or higher |
| E96-130 (VCPE) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||