Home › Engine / Hybrid System ยท 6AR-FSE › FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
(Click here)


2. DRAIN FUEL


3. REMOVE CENTER EXHAUST PIPE ASSEMBLY
(Click here)


4. REMOVE NO. 2 FLOOR UNDER COVER


  1. for TMC Made:



      C310499
    1. Remove the screw and 2 clips.
      Text in Illustration 
      V100135
      Nut (attached to under cover)
      V100136
      Screw

    2. Disengage the 6 nuts and remove the No. 2 floor under cover.

      HINT:
      The 6 nuts will remain attached to the No. 2 floor under cover.



  1. for TMMR Made:



      C309401
    1. Remove the 2 clips.
      Text in Illustration 
      V100135
      Nut (attached to under cover)

    2. Disengage the 6 nuts and remove the No. 2 floor under cover.

      HINT:
      The 6 nuts will remain attached to the No. 2 floor under cover.



5. REMOVE NO. 1 FLOOR UNDER COVER


  1. for TMC Made:



      C310498
    1. Remove the screw.
      Text in Illustration 
      V100135
      Nut (attached to under cover)
      V100136
      Screw

    2. Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.

      HINT:
      Rotate the clips to disengage them. The 5 nuts and 2 clips will remain attached to the No. 1 floor under cover.



  1. for TMMR Made:



      C309402
    1. Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.
      Text in Illustration 
      V100135
      Nut (attached to under cover)

      HINT:
      Rotate the clips to disengage them. The 5 nuts and 2 clips will remain attached to the No. 1 floor under cover.



6. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY


    A339046
  1. Remove the bolt and nut, and separate the No. 2 parking brake cable assembly.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut



7. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    A339047
  1. Remove the bolt and nut, and separate the No. 3 parking brake cable assembly.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut



8. REMOVE REAR NO. 1 STABILIZER BAR BRACKET


    A255957
  1. Remove the 4 bolts and 2 rear No. 1 stabilizer bar brackets.



9. REMOVE LOWER CENTER FUEL TANK PROTECTOR


    A135224
  1. Remove the 4 bolts and lower center fuel tank protector.



10. DISCONNECT FUEL PUMP TUBE SUB-ASSEMBLY


    A338485E01
  1. Disconnect the fuel pump tube sub-assembly.
    Text in Illustration 
    *a
    Fuel Pipe
    *b
    Retainer
    *c
    Nylon Tube
    *d
    Fuel Tube Connector
    *e
    O-ring
    *f
    Claw
    V100135
    Push
    V100136
    Pull out
    V100137
    Pull off

    NOTICE:
    Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


    1. Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

      NOTICE:
      Be sure to disconnect the fuel tube connector by hand.

    2. If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

      NOTICE:
      1. Be sure to disconnect the fuel tube connector by hand.
      2. Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
      3. Do not bend, twist, pinch or kink the nylon tube.

    3. Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.

    4. Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



11. REMOVE FUEL TANK ASSEMBLY


    A137480
  1. Slide the clip and disconnect the fuel emission hose from the charcoal canister assembly.



    A254980
  1. Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.



    A255933
  1. Loosen the clamp, then disconnect the breather tube fuel hose from the fuel tank assembly.



    A255934
  1. Support the fuel tank assembly using an engine lifter.

    HINT:
    Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



    A255935
  1. Remove the 2 bolts of the fuel tank bands.

  1. Lower the engine lifter to remove the fuel tank assembly.

    NOTICE:
    1. Slowly operate the engine lifter to lower the fuel tank assembly.
    2. Be careful not to drop the fuel tank assembly.
    3. When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.



    A079478E01
  1. Remove the 2 pins and 2 fuel tank bands as shown in the illustration.
    Text in Illustration 
    *1
    Pin
    *2
    Fuel Tank Band



    A338487
  1. Remove the 4 clip nuts from the fuel tank assembly.



12. REMOVE NO. 1 FUEL TANK CUSHION


    A338488
  1. Remove the No. 1 fuel tank cushion from the fuel tank assembly.



13. REMOVE NO. 2 FUEL TANK CUSHION


    A338489
  1. Remove the 7 No. 2 fuel tank cushions from the fuel tank assembly.



14. REMOVE NO. 2 FUEL TANK PROTECTOR


    A296961
  1. Disengage the 2 claws and remove the No. 2 fuel tank protector by sliding it as shown in the illustration.



15. REMOVE NO. 3 FUEL TANK PROTECTOR


    A296962
  1. Disengage the 2 claws and remove the No. 3 fuel tank protector by sliding it as shown in the illustration.



16. REMOVE FUEL CUT OFF WITH TUBE VALVE ASSEMBLY


    A338490E01
  1. Slide the clip and disconnect the fuel emission hose from the fuel cut off with tube valve assembly.
    Text in Illustration 
    *1
    Fuel Tank Breather Tube Gasket
    *2
    Fuel Cut Off with Tube Valve Assembly
    *3
    Fuel Emission Hose
    *a
    Fuel Cut Off Valve

  1. Disengage the 2 clamps to disconnect the fuel cut off with tube valve assembly from the fuel tank assembly.

  1. Insert a clip remover between the fuel cut off valve and fuel tank breather tube gasket and remove the fuel cut off valve by gradually pushing it upward.

    NOTICE:
    1. Work carefully to maintain the sealing integrity of the fuel cut off valve as it is made from resin and easy to be damaged if forcibly removing and installing it.
    2. Be sure to install a new fuel cut off with tube valve assembly and 2 new fuel tank breather tube gaskets.

  1. Remove the 2 fuel tank breather tube gaskets from the fuel tank assembly.



17. REMOVE FUEL PUMP TUBE SUB-ASSEMBLY


    A338481
  1. Disengage the 4 clamps to remove the fuel pump tube sub-assembly from the fuel tank assembly.



18. REMOVE FUEL MAIN TUBE SUPPORT


    A338482
  1. Remove the bolt and fuel main tube support from the fuel tank assembly.



19. REMOVE NO. 1 FUEL TUBE CLAMP


    A338483
  1. Disengage the 2 claws to remove the 2 No. 1 fuel tube clamps from the fuel tank assembly.



20. REMOVE NO. 2 FUEL TUBE CLAMP


    A338484
  1. Disengage the claw to remove the No. 2 fuel tube clamp from the fuel tank assembly.