Home › Brake › BRAKE SYSTEM (OTHER) › VACUUM PUMP (for 2GR-FKS)
RM33A0E _54 Brake _065366 BRAKE SYSTEM (OTHER) _0319139 VACUUM PUMP(for 2GR-FKS) A

BRAKE SYSTEM (OTHER)  VACUUM PUMP(for 2GR-FKS)  INSTALLATION  


PROCEDURE

Hide 29300 1.INSTALL VACUUM PUMP ASSEMBLY

a.

When using a new vacuum pump assembly:

i.
C338027C01
1.792,1.24 2.177,0.563 2.177,0.563 2.49,0.563 true 1.24,1.917 1.469,1.917 1.469,1.917 1.469,1.656 true 2.521,0.5 2.833,0.656 0.313,0.156 10 false *1 1.083,1.844 1.396,2 0.313,0.156 10 false *2
*1 No. 2 O-ring
*2 No. 3 O-ring
V100135

Engine oil


Apply engine oil to the No. 2 O-ring and No. 3 O-ring which are installed to a new vacuum pump assembly.



b.

When reusing the vacuum pump assembly:

i.
C338027C01
1.792,1.24 2.177,0.563 2.177,0.563 2.49,0.563 true 1.24,1.917 1.469,1.917 1.469,1.917 1.469,1.656 true 2.521,0.5 2.833,0.656 0.313,0.156 10 false *1 1.083,1.844 1.396,2 0.313,0.156 10 false *2
*1 No. 2 O-ring
*2 No. 3 O-ring
V100135

Engine oil


Apply engine oil to a new No. 2 O-ring and No. 3 O-ring and install them to the vacuum pump assembly.



c.

Apply engine oil to the inner surface of the installation hole.


d.
C375939C01
1.948,1.177 1.948,0.635 1.948,0.635 1.688,0.635 true 0.927,1.49 1.24,1.49 1.24,1.49 1.24,1.219 true 1.323,1.75 1.563,1.75 1.563,1.75 1.833,1.323 true 1.49,0.542 1.677,0.719 0.188,0.177 10 true *a 0.75,1.406 0.927,1.583 0.177,0.177 10 true *b 1.135,1.677 1.313,1.854 0.177,0.177 10 true *c
*a Coupling Teeth
*b Groove
*c Oil Pipe


Temporarily install the vacuum pump assembly so that the oil pipe engages with the hole of the camshaft and the coupling teeth engages with the groove of the camshaft.

NOTICE:
·

Ensure that the vacuum pump assembly is installed securely.

·

Be careful not to pinch the O-ring.




e.
C375938N01
0.573,1.177 0.698,1.365 0.125,0.188 10 true 1 2.219,1.396 2.344,1.583 0.125,0.188 10 true 2 1.427,1.979 1.552,2.167 0.125,0.188 10 true 3

Install the vacuum pump assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

After installation, check that there are no gaps between the matching surfaces and that the vacuum pump assembly is not installed at an angle.

·

Tighten the 3 bolts in the order shown in the illustration.




Hide 17361M 2.CONNECT AIR TUBE

a.
C375935

Connect the air tube to the vacuum pump assembly and slide the clip to secure it.


Hide 82121 3.INSTALL ENGINE WIRE

a.
C375937

Install the earth wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
C375936

Install the engine wire with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17126 4.INSTALL NO. 2 SURGE TANK STAY

a.
A408128N01
1.906,1.76 2.063,1.958 0.156,0.198 10 true 1 2.198,1.073 2.354,1.271 0.156,0.198 10 true 2

Install the No. 2 surge tank stay with the 2 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 22030 5.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY