The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front frame assembly removal/installation are shown below.
1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
23825
2.REMOVE FUEL DELIVERY GUARD (for A25A-FKS)
3.INSTALL ENGINE HANGER
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
45319
4.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)
for A25A-FKS:
Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>REMOVAL
5.DISCONNECT WIRE HARNESS
for LHD: Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>REMOVAL
for RHD: Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>REMOVAL
6.REMOVE FRONT FRAME ASSEMBLY
Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.
Remove the 4 nuts and separate the rear engine mounting insulator from the front frame assembly.
7.REMOVE FRONT STABILIZER BAR WITH BRACKET
for A25A-FKS: Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>REMOVAL
for 2AR-FE, 2GR-FKS: Click hereSteering>STEERING GEAR / LINKAGE>STEERING GEAR>REMOVAL
44250
8.REMOVE RACK AND PINION POWER STEERING GEAR ASSEMBLY
48069
9.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly.
48068
10.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
17572B
11.REMOVE NO. 2 EXHAUST PIPE SUPPORT BRACKET
Remove the 2 bolts and No. 2 exhaust pipe support bracket from the front frame assembly.
51227B
12.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER (for A25A-FKS, 2GR-FKS)
Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.
13.REMOVE BOLT (for 2AR-FE)
Remove the 2 bolts from the front frame assembly.
52213A
14.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER
Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.
52216B
15.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER
Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.
52211J
16.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for LH Side)
| *a | Flange |
Using a chisel and hammer, kink the flange of the front suspension member body mounting front cushion as shown in the illustration.
Apply lubricant to the contact surfaces of the front suspension member body mounting front cushion.
| *1 | Front Suspension Member Body Mounting Front Cushion |
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Turn the SST center bolt as shown in the illustration to create a clearance between the front suspension member body mounting front cushion and the front frame assembly.
While applying lubricant to the front suspension member body mounting front cushion through the clearance, gradually remove the front suspension member body mounting front cushion.
Tighten SST slowly and evenly.
Be careful as the mounting cushion may fly out.
The mounting cushion cannot be reused.
52211J
17.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION (for RH Side)
Perform the same procedure as for the LH side.
52217E
18.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH
| *a | Flange |
Using a chisel and hammer, kink the flange of the front suspension member body mounting rear cushion LH as shown in the illustration.
Apply lubricant to the contact surfaces of the front suspension member body mounting rear cushion LH.
| *1 | Front Suspension Member Body Mounting Rear Cushion LH |
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Turn the SST center bolt as shown in the illustration to create a clearance between the front suspension member body mounting rear cushion LH and the front frame assembly.
While applying lubricant to the front suspension member body mounting rear cushion LH through the clearance, gradually remove the front suspension member body mounting rear cushion LH.
Tighten SST slowly and evenly.
Be careful as the mounting cushion may fly out.
The mounting cushion cannot be reused.
52215
19.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION
Perform the same procedure as for the front suspension member body mounting rear cushion LH.
20.REMOVE HOLE PLUG
Remove the 7 hole plugs from the front frame assembly.
There are 2 different shapes of hole plug.