Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320457 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Wiper Motor Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit for the windshield wiper motor assembly.

WIRING DIAGRAM

E366179E05
2.031,0.583 2.948,0.781 0.917,0.198 10 false from Battery 1.104,0.76 2.021,0.958 0.917,0.198 10 false WIPER 4.844,0.573 5.76,0.771 0.917,0.198 10 false +B 4.844,0.854 5.76,1.052 0.917,0.198 10 false GND 4.458,1.281 7.156,1.615 2.698,0.333 10 false Windshield Wiper Motor Assembly 4.469,1.146 4.813,1.333 0.344,0.188 10 false A31 4.229,0.729 5.271,0.99 1.042,0.26 10 false 1*1, 4*2 4.229,0.458 5.188,0.781 0.958,0.323 10 false 4*1, 1*2 4.104,2.427 4.448,2.615 0.344,0.188 10 false 21 4.344,2.427 4.948,2.656 0.604,0.229 10 false WPS 4.135,2.938 4.479,3.125 0.344,0.188 10 false K52 4.125,3.104 7.083,3.344 2.958,0.24 10 false Main Body ECU (Multiplex Network Body ECU) 1.563,2.833 2.479,3.031 0.917,0.198 10 false WIPER 2.083,2.146 2.427,2.333 0.344,0.188 10 false 5 1.417,2.427 1.76,2.615 0.344,0.188 10 false 2 1.417,2.125 1.76,2.313 0.344,0.188 10 false 3 2.083,2.427 2.427,2.615 0.344,0.188 10 false 1 4.802,2.052 5.406,2.281 0.604,0.229 10 false IG 5.042,2.052 5.646,2.281 0.604,0.229 10 false +B 0.26,3.344 1.177,3.542 0.917,0.198 10 false *1: for LHD 1.292,3.344 2.208,3.542 0.917,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Wiper / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Wiper > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Motor Power Supply Voltage Front wiper motor assembly supply voltage status Min.: 0 V
Max.: 63 V
Almost the same as actual front wiper motor assembly voltage -
Body Electrical > Wiper > Data List
Tester Display
Motor Power Supply Voltage
50003 384 37
OK:

The GTS display is normal.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A31 windshield wiper motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A31-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A31-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A31-4 (+B) - Body ground Ignition switch ON 11 to 14 V
Less than approximately 60 seconds after ignition switch turned off 11 to 14 V
Approximately 60 seconds after ignition switch turned off Below 1 V

for RHD
Tester Connection Condition Specified Condition
A31-1 (+B) - Body ground Ignition switch ON 11 to 14 V
Less than approximately 60 seconds after ignition switch turned off 11 to 14 V
Approximately 60 seconds after ignition switch turned off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

NG

4.INSPECT WIPER RELAY
4.INSPECT WIPER RELAY
a.

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WIPER RELAY)

NG

REPLACE WIPER RELAY

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WIPER RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (WIPER relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (WIPER RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (WIPER RELAY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (WIPER relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (WIPER RELAY - WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (WIPER RELAY - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
5 (WIPER relay) - A31-4 (+B) Always 10 kΩ or higher
5 (WIPER relay) or A31-4 (+B) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
5 (WIPER relay) - A31-1 (+B) Always 10 kΩ or higher
5 (WIPER relay) or A31-1 (+B) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (WIPER RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WIPER RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K52 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (WIPER relay) - K52-21 (WPS) Always Below 1 Ω
1 (WIPER relay) or K52-21 (WPS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR