Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › CAMSHAFT › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321403 CAMSHAFT A

2AR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform inspection after repair after replacing the camshaft, No. 2 camshaft, camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11821 1.INSTALL NO. 2 CAMSHAFT BEARING

Hide 11811 2.INSTALL NO. 1 CAMSHAFT BEARING

Hide 13070A 3.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A196902C34
1.896,0.656 1.771,0.656 1.771,0.656 1.594,0.927 false 1.219,0.167 1.094,0.167 1.094,0.167 0.656,0.792 true 1.302,0.083 1.469,0.25 0.167,0.167 10 false *b 1.969,0.573 2.281,0.771 0.313,0.198 10 false *a
*a Knock Pin
*b Knock Pin Hole


Align and fit the knock pin of the No. 2 camshaft to the knock pin hole of the camshaft timing exhaust gear assembly.


b.
A350374C03
0.75,0.781 0.875,0.781 0.875,0.781 0.875,1.26 true 2.667,0.958 2.521,1.271 2.521,1.271 2.365,1.271 true 0.469,0.708 0.927,0.906 0.458,0.198 10 false SST 2.188,1.177 2.5,1.375 0.313,0.198 10 false *a
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure the SST and No. 2 camshaft in a vise as shown in the illustration and check that the camshaft timing exhaust gear assembly does not rotate.

SST
09212-31010  

NOTICE:
·

Do not damage the No. 2 camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




c.
A196904C92
2.146,0.854 1.896,0.854 1.896,0.854 1.5,1.073 false 0.823,0.76 0.917,0.76 0.917,0.76 1.125,0.979 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 0.156,0.146 0.333,0.313 0.177,0.167 10 false *a 0.146,1.927 0.344,2.083 0.198,0.156 10 false *b 1.802,0.542 2.115,0.74 0.313,0.198 10 false *c 2.198,0.771 2.375,0.927 0.177,0.156 10 false *2 1.771,2.031 1.948,2.188 0.177,0.156 10 false *d
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Flange
*a Incorrect
*b Correct
*c Clearance
*d No Clearance


Check that there is no clearance between the camshaft timing exhaust gear assembly and camshaft flange.


d.

While securely holding the No. 2 camshaft, install the bolt of the camshaft timing exhaust gear assembly by hand.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:

Do not disassemble the camshaft timing exhaust gear assembly.


HINT:

Perform inspection after repair after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



e.

Check the lock of the camshaft timing exhaust gear assembly.

i.

Make sure that the camshaft timing exhaust gear assembly is locked.

NOTICE:

Be careful not to damage the No. 2 camshaft.




f.

Release the lock pin.

A284097C31
1.417,1.052 1.771,1.052 1.771,1.052 1.917,1.104 true 2.344,1.229 2.479,1.125 2.479,1.125 2.781,1.125 true 2.542,2.552 2.677,2.448 2.677,2.448 2.906,2.448 true 2.115,2.792 2.281,2.958 2.281,2.958 2.906,2.958 true 1.344,2.552 1.635,2.552 1.635,2.552 1.771,2.427 true 4.813,1.156 5.073,1.156 5.073,1.156 5.323,1.604 true 4.615,1.51 4.76,1.51 4.76,1.51 5.094,1.76 true 4.615,2.521 4.813,2.521 4.813,2.521 5.125,2.135 true 5.604,1.771 5.948,1.448 5.948,1.448 6.146,1.448 true 5.552,2.167 5.885,2.469 5.885,2.469 6.094,2.469 true 2.958,2.354 3.271,2.51 0.313,0.156 10 false *e 2.958,2.865 3.271,3.021 0.313,0.156 10 false *f 4.615,1.073 4.885,1.323 0.271,0.25 10 false *g 1.229,0.948 1.542,1.104 0.313,0.156 10 false *a 2.844,1.031 3.156,1.188 0.313,0.156 10 false *b 4.438,1.406 4.75,1.563 0.313,0.156 10 false *c 4.448,2.417 4.76,2.573 0.313,0.156 10 false *d 6.135,2.365 6.448,2.521 0.313,0.156 10 false *d 6.188,1.344 6.5,1.5 0.313,0.156 10 false *d 1.198,2.469 1.51,2.625 0.313,0.156 10 false A
*a Retard Side Path *b Advance Side Path
*c Open *d Close
*e Rubber Piece *f Vinyl Tape
*g Knock Pin - -


i.

Clean the camshaft journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the No. 2 camshaft. Plug 3 of the oil paths with rubber pieces.



iii.

Make a hole in the tape over the port (A) shown in the illustration.


iv.
A196906

While applying approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the oil path, forcibly turn the camshaft timing exhaust gear assembly in the advance direction (counterclockwise).

CAUTION:

Cover the oil paths with a piece of cloth when applying air pressure to prevent oil from spraying.


NOTICE:

Do not allow the camshaft timing exhaust gear assembly to lock. If it locks, release the lock pin again.


HINT:
·

Depending on the air pressure applied, the camshaft timing exhaust gear assembly may turn in the advance direction without assistance by hand.

·

If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.





g.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear assembly within its movable range (26.5 to 28.5°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.

NOTICE:
·

Do not use air pressure to perform the smooth operation check.

·

Do not allow the camshaft timing exhaust gear assembly to lock. If it locks, release the lock pin again.





h.

Remove the vinyl tape and rubber pieces from the No. 2 camshaft.


i.

Remove the bolt and camshaft timing exhaust gear assembly.


Hide 15678A 4.INSTALL OIL CONTROL VALVE FILTER

Hide 13070A 5.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A350373C03
0.719,0.74 0.854,0.74 0.854,0.74 0.854,1.25 true 2.729,1 2.573,1.25 2.573,1.25 2.333,1.25 true 0.427,0.667 0.885,0.865 0.458,0.198 10 false SST 2.146,1.156 2.458,1.354 0.313,0.198 10 false *a
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure the SST and No. 2 camshaft in a vise as shown in the illustration.

SST
09212-31010  

NOTICE:
·

Do not damage the No. 2 camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




b.
A250991

Install the camshaft timing exhaust gear assembly to the No. 2 camshaft with the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


Hide 6.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A260580C08
1.833,0.802 2.104,0.615 2.104,0.615 2.26,0.615 true 2.313,0.521 2.531,0.729 0.219,0.208 10 false *a
*a Timing Notch (Groove)


Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover sub-assembly are aligned.


Hide 13512 7.INSTALL NO. 2 CAMSHAFT

a.
A407987C01
0.677,1.167 1.115,1.167 true 2.667,1.25 2.906,1.25 false 1.802,0.51 1.958,0.344 1.958,0.344 2.219,0.344 false 2.281,0.26 2.594,0.458 0.313,0.198 10 false *1 2.958,1.146 3.271,1.344 0.313,0.198 10 false *2 0.521,1.052 0.833,1.25 0.313,0.198 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.

Clean the camshaft journals.


c.

Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


d.
A250992C11
2.25,3.375 2.594,3.26 2.594,3.26 2.76,3.26 true 2.146,3.604 2.615,3.865 2.615,3.865 2.792,3.865 true 2.813,3.188 3,3.354 0.188,0.167 10 false *a 2.854,3.792 3.042,3.958 0.188,0.167 10 false *b
*a Paint Mark
*b Timing mark


Hold up the chain sub-assembly and align the timing mark and the paint mark, and install the No. 2 camshaft.

HINT:

Perform inspection after repair after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13511 8.INSTALL CAMSHAFT

a.
A407987C01
0.677,1.167 1.115,1.167 true 2.667,1.25 2.906,1.25 false 1.802,0.51 1.958,0.344 1.958,0.344 2.219,0.344 false 2.281,0.26 2.594,0.458 0.313,0.198 10 false *1 2.958,1.146 3.271,1.344 0.313,0.198 10 false *2 0.521,1.052 0.833,1.25 0.313,0.198 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.

Clean the camshaft journals.


c.

Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


d.
A251007C11
1.042,2.677 0.813,2.604 0.813,2.604 0.646,2.604 true 1.167,2.167 1.354,2.333 0.188,0.167 10 false *a 0.49,2.521 0.677,2.688 0.188,0.167 10 false *b
*a Approximately 17°
*b Knock Pin


Install the camshaft to the camshaft housing sub-assembly as shown in the illustration.

HINT:

Perform inspection after repair after replacing the camshaft.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 9.INSTALL CAMSHAFT BEARING CAP

a.
A413677N01
0.74,0.052 0.896,0.25 0.156,0.198 10 false 1 1.219,0.052 1.375,0.25 0.156,0.198 10 false 2 1.781,0.052 1.938,0.25 0.156,0.198 10 false 3 2.344,0.052 2.5,0.25 0.156,0.198 10 false 4 2.896,0.052 3.052,0.25 0.156,0.198 10 false 5

Confirm the marks and numbers on the No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps and place them and the No. 1 camshaft bearing cap in their proper positions and directions.


b.
A284106N05
1.729,0.333 1.885,0.531 0.156,0.198 10 1 1.74,1.771 1.896,1.969 0.156,0.198 10 2 2.313,0.344 2.469,0.542 0.156,0.198 10 3 2.354,1.792 2.51,1.99 0.156,0.198 10 4 1.156,0.344 1.313,0.542 0.156,0.198 10 5 1.135,1.792 1.292,1.99 0.156,0.198 10 6 2.885,0.344 3.042,0.542 0.156,0.198 10 7 2.948,1.781 3.104,1.979 0.156,0.198 10 8 0.594,0.313 0.75,0.51 0.156,0.198 10 9 0.521,1.938 0.833,2.135 0.313,0.198 10 10

Uniformly tighten the 10 bolts in several steps in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


c.
A347101C03
0.375,0.76 0.583,0.76 true 1.24,1.146 1.458,2.01 1.458,2.01 1.604,2.01 true 1.792,1.01 2,1.01 true 2.396,1.01 2.604,1.01 true 2.927,0.708 3.135,0.708 true 1.74,1.573 1.896,1.771 0.156,0.198 10 false 1 2.323,1.594 2.479,1.792 0.156,0.198 10 false 3 2.906,1.573 3.063,1.771 0.156,0.198 10 false 7 2.833,0.031 2.99,0.229 0.156,0.198 10 false 8 2.271,0.031 2.427,0.229 0.156,0.198 10 false 4 1.74,0.01 1.896,0.208 0.156,0.198 10 false 2 1.177,0.031 1.333,0.229 0.156,0.198 10 false 6 0.552,0 0.865,0.24 0.313,0.24 10 false 10 0.167,1.156 0.323,1.354 0.156,0.198 10 false 9 0.49,1.833 0.74,2.031 0.25,0.198 10 false 11 1.104,1.583 1.26,1.781 0.156,0.198 10 false 5 0.125,0.656 0.333,0.854 0.208,0.198 10 true *1 1.677,1.938 1.885,2.135 0.208,0.198 10 true *2 2.063,0.906 2.271,1.104 0.208,0.198 10 true *3 2.615,0.917 2.823,1.115 0.208,0.198 10 true *3 3.167,0.625 3.375,0.823 0.208,0.198 10 true *3
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap


Uniformly tighten the 11 bolts in several steps in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


d.

Check the torque of each bolt again.


Hide 13050 10.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.
A284096C38
0.865,1.729 1.021,1.729 1.021,1.729 1.781,1.333 true 0.771,3.969 0.927,3.969 0.927,3.969 1.688,3.573 true 2.031,1.594 2.448,1.938 2.448,1.938 2.604,1.938 true 2.073,3.677 2.438,3.417 2.438,3.417 2.583,3.417 true 0.083,0.25 0.396,0.406 0.313,0.156 10 false *a 0.083,2.583 0.396,2.74 0.313,0.156 10 false *b 0.708,1.625 1.021,1.781 0.313,0.156 10 false *c 2.667,1.844 2.979,2 0.313,0.156 10 false *d 2.635,3.323 2.948,3.479 0.313,0.156 10 false *d 0.604,3.854 0.917,4.01 0.313,0.156 10 false *c
*a Advanced Position
*b Retarded Position
*c Knock Pin Hole
*d Alignment Mark


Check the camshaft timing gear assembly position.

NOTICE:
·

If the camshaft timing gear assembly is set to the advanced position, do not let the camshaft timing gear assembly rotate clockwise during installation.

·

If the camshaft timing gear assembly has rotated to the most retarded position, make sure to release the lock pin and set the camshaft timing gear assembly to the most advanced position before tightening the camshaft timing gear assembly.




b.
A251004C02
2.043,2.092 2.214,2.252 0.171,0.16 10 *a 2.109,3.019 2.28,3.178 0.171,0.16 10 *b
*a Narrow
*b Wide


Install the camshaft timing gear assembly as shown in the illustration.


c.
A250998C02
1.164,2.02 1.352,2.184 0.188,0.164 10 *a 2.678,2.974 2.866,3.138 0.188,0.164 10 *a 1.216,2.951 1.404,3.115 0.188,0.164 10 *b 2.74,2.034 2.928,2.198 0.188,0.164 10 *b
*a Narrow
*b Wide


Turn the camshaft timing gear assembly approximately 180° counterclockwise.


d.
A250999C16
1.396,0.75 0.854,0.448 0.854,0.448 0.563,0.448 true 1.375,1 0.354,1 true 0.396,0.375 0.573,0.542 0.177,0.167 10 false *a 0.167,0.927 0.344,1.094 0.177,0.167 10 false *b
*a Paint Mark
*b Timing Mark


Align the paint mark with the timing mark and install the chain sub-assembly to the camshaft timing gear assembly.


e.
A196901C79
1.979,0.625 1.854,0.625 1.854,0.625 1.635,0.906 false 1.25,0.208 1.125,0.208 1.125,0.208 0.698,0.771 true 1.302,0.115 1.479,0.292 0.177,0.177 10 false *a 2.021,0.542 2.188,0.719 0.167,0.177 10 false *b
*a Knock Pin Hole
*b Knock Pin


Align and attach the knock pin of the camshaft with the knock pin hole of the camshaft timing gear assembly.


f.
A196904C92
2.146,0.854 1.896,0.854 1.896,0.854 1.5,1.073 false 0.823,0.76 0.917,0.76 0.917,0.76 1.125,0.979 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 0.156,0.146 0.333,0.313 0.177,0.167 10 false *a 0.146,1.927 0.344,2.083 0.198,0.156 10 false *b 1.802,0.542 2.115,0.74 0.313,0.198 10 false *c 2.198,0.771 2.375,0.927 0.177,0.156 10 false *2 1.771,2.031 1.948,2.188 0.177,0.156 10 false *d
*1 Camshaft Timing Gear Assembly
*2 Camshaft Flange
*a Incorrect
*b Correct
*c Gap
*d No Gap


Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.


g.

While securely holding the camshaft, install the bolt of the camshaft timing gear assembly by hand.

NOTICE:

Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.



h.

If the lock pin has not been released, release it.

i.
A249942C11
1.063,0.979 0.563,0.688 0.563,0.688 0.417,0.688 true 0.354,0.99 0.542,0.99 0.542,0.99 1.115,1.125 true 0.26,0.594 0.438,0.76 0.177,0.167 10 false *b 0.198,0.906 0.375,1.073 0.177,0.167 10 false *a
*a Make a Hole
*b Adhesive Tape Sealing Area


After cleaning the intake side VVT oil hole of the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



ii.

Make a hole in the adhesive tape as shown in the illustration.


iii.
A251001

Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the open hole to release the lock pin.

NOTICE:
·

If air leaks out, reattach the adhesive tape.

·

Cover the hole with a piece of cloth when applying air pressure to prevent oil from spraying.




iv.

Forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

HINT:
·

Depending on the air pressure applied, the camshaft timing gear assembly may turn in the advance direction without assistance by hand.

·

If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.




v.

Remove the adhesive tape from the No. 1 camshaft bearing cap.



i.
A249935

Using a wrench to hold the hexagonal portion of the camshaft, install the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.



j.
A252822C11
0.969,0.917 1.833,0.271 1.833,0.271 2.917,0.938 true 0.979,1.104 1.865,1.646 1.865,1.646 2.948,1.125 true 1.802,0.052 1.99,0.24 0.188,0.188 10 true *a 1.792,1.667 1.979,1.854 0.188,0.188 10 true *b
*a Paint Mark
*b Timing Mark


Check that the timing marks on the camshaft timing gear sub-assembly and camshaft timing exhaust gear assembly are facing upward as shown in the illustration.

HINT:

Perform inspection after repair after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13540 13.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A245327N08
1.979,0.208 2.25,0.385 0.271,0.177 10 10°

Turn the crankshaft pulley approximately 10° clockwise.


b.

Install a new gasket and the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Be careful not to drop the gasket inside the timing chain cover sub-assembly.



c.

Remove the pin from the stopper plate.


Hide 14.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover sub-assembly are aligned.

A292248C12
0.396,1.75 0.583,1.75 0.583,1.75 1.167,2.083 true 2.677,2.125 3.208,1.792 3.208,1.792 3.344,1.792 true 0.552,2.271 1.573,2.271 true 2.823,2.531 3.333,2.198 3.333,2.198 3.49,2.198 true 5.031,1.083 5.458,0.708 5.458,0.708 5.635,0.708 true 5.031,1.167 5.948,1.656 5.948,1.656 6.135,1.656 true 0.198,1.635 0.51,1.792 0.313,0.156 10 false *c 6.188,1.563 6.438,1.76 0.25,0.198 10 false *d 1.25,0.052 1.563,0.208 0.313,0.156 10 false *a 2.448,0.115 2.76,0.271 0.313,0.156 10 false *b 3.396,1.729 3.708,1.885 0.313,0.156 10 false *c 0.385,2.188 0.542,2.385 0.156,0.198 10 false A 3.563,2.125 3.719,2.323 0.156,0.198 10 false A 5.708,0.615 5.958,0.813 0.25,0.198 10 false *e
*a Approximately 7° *b Approximately 32°
*c Timing Mark *d Timing Notch (Groove)
*e Timing Mark "0°" - -



b.

Check that the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are facing upward as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.

HINT:

"A" is not a timing mark.



Hide 11324 15.INSTALL TIMING CHAIN COVER PLATE

a.

Install a new gasket and the timing chain cover plate with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16.INSTALL TIMING CHAIN COVER TIGHT PLUG

Hide 11201 17.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 82121 19.CONNECT ENGINE WIRE

a.

Connect the engine wire to the engine and install the bolts and nuts.

A407963C01
5.615,2.813 5.75,2.979 0.135,0.167 10 true A 5.667,2.583 5.802,2.75 0.135,0.167 10 true A 6.292,3.156 6.427,3.323 0.135,0.167 10 true A 6.729,3.021 6.865,3.188 0.135,0.167 10 true A 6.448,1.25 6.583,1.417 0.135,0.167 10 true A 5.76,1.396 5.896,1.563 0.135,0.167 10 true A 1.271,3.333 1.406,3.5 0.135,0.167 10 true A 1.604,0.885 1.74,1.052 0.135,0.167 10 true B
V100136

Bolt
V100137

Nut


Torque:
(A) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
(B) : 9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.

Connect the connectors and engage the clamps.


Hide 20.CONNECT HOSES

Engage the 3 clamps.

Hide 21.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 23.INSPECT FOR ENGINE OIL LEAK

Hide 17750A 24.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 12601B 25.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53295E 26.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53736 27.INSTALL FRONT FENDER APRON SEAL RH

Hide 28.INSTALL FRONT WHEEL RH