Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321404 CYLINDER HEAD GASKET A

2AR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform inspection after repair after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11101A 1.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 3.INSTALL CYLINDER HEAD GASKET

a.

Clean the cylinder block sub-assembly and cylinder head sub-assembly with solvent.


b.
A344904C06
2.229,0.604 2.458,0.188 2.458,0.188 2.646,0.188 false 2.365,3.906 2.49,3.906 2.49,3.906 2.49,3.323 true 2.698,0.094 3.01,0.292 0.313,0.198 10 false *a 1.156,0.271 1.469,0.469 0.313,0.198 10 false *c 0.51,1.188 0.823,1.385 0.313,0.198 10 false *b 1.146,1.698 1.458,1.896 0.313,0.198 10 false *c 0.427,3.885 0.74,4.083 0.313,0.198 10 false *g 0.167,3.01 0.479,3.208 0.313,0.198 10 false *f 0.771,4.24 1.083,4.438 0.313,0.198 10 false *h 2.969,2.74 3.281,2.938 0.313,0.198 10 false *d 0.198,3.5 0.51,3.698 0.313,0.198 10 false *e 2.188,3.792 2.5,3.99 0.313,0.198 10 false *1 3.104,2.979 3.417,3.177 0.313,0.198 10 false *d 3.01,3.698 3.323,3.896 0.313,0.198 10 false *d 0.76,2.135 0.917,2.333 0.156,0.198 10 false A 2.344,2.542 2.5,2.74 0.156,0.198 10 false A
*1 Cylinder Head Gasket
*a Lot No.
*b Front of Engine
*c Seal Packing
*d 3.0 to 5.0 mm (0.118 to 0.197 in.)
*e 38 mm (1.50 in.)
*f 152.5 mm (6.00 in.)
*g 7.0 to 9.0 mm (0.276 to 0.354 in.)
*h 5.0 to 7.0 mm (0.197 to 0.276 in.)


Apply a continuous line of seal packing to a new cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head gasket within 3 minutes and tighten the cylinder head bolts within 15 minutes of applying seal packing.




c.

Place the cylinder head gasket on the cylinder block sub-assembly with the Lot No. stamp facing upward.

NOTICE:

Pay attention to the installation direction.



Hide 11101 4.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head bolts are tightened in 4 progressive steps.


a.

Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:
·

Ensure that no oil is on the contact surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket with the bottom of the cylinder head sub-assembly.




b.

Install the 10 plate washers to the 10 cylinder head bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


d.

Step 1:

i.
A284098N03
1.5,1.677 1.656,1.875 0.156,0.198 10 1 1.49,0.292 1.646,0.49 0.156,0.198 10 2 1.958,1.677 2.115,1.875 0.156,0.198 10 3 1.948,0.292 2.104,0.49 0.156,0.198 10 5 2.427,1.677 2.583,1.875 0.156,0.198 10 7 2.406,0.292 2.563,0.49 0.156,0.198 10 9 1.021,1.667 1.177,1.865 0.156,0.198 10 6 1.042,0.292 1.198,0.49 0.156,0.198 10 4 0.51,1.656 0.771,1.854 0.26,0.198 10 10 0.583,0.292 0.74,0.49 0.156,0.198 10 8

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

Do not drop the plate washer for the cylinder head bolt into the cylinder head sub-assembly.




e.

Step 2:

i.

Check that the cylinder head bolts are tightened to the specified torque.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)



f.

Step 3:

i.
A196910C04
1.098,1.567 1.28,1.751 0.181,0.184 10 *a 0.896,0.378 1.195,0.539 0.3,0.161 10 90° 2.585,0.378 2.885,0.539 0.3,0.161 10 90° 1.239,1.567 1.497,1.156 false
*a Paint Mark
V100136

Front of Engine


Mark each cylinder head bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head bolts 90° in the order shown in step 1.



g.

Step 4:

i.

Tighten the cylinder head bolts another 90° in the order shown in step 1.


ii.

Check that the paint marks are now facing rearward.

NOTICE:
·

Do not install the timing chain cover sub-assembly for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

Thoroughly wipe off any seal packing that has seeped out onto the front side of the engine.



HINT:

Perform inspection after repair after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Hide 13716 5.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem cap ends.


b.

Install the 16 valve stem caps to the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the valve stem caps into the cylinder head sub-assembly.



Hide 13750 6.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect the 16 valve lash adjuster assemblies before installing them.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


b.

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

HINT:

Install each valve lash adjuster assembly to the same place it was removed from.



Hide 13801 7.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply engine oil to the valve lash adjuster assembly tips and valve stem caps.


b.
A407987C02
1.833,0.531 2.052,0.313 2.052,0.313 2.281,0.313 false 2.667,1.271 2.938,1.271 false 0.677,1.115 1.104,1.115 true 2.333,0.24 2.646,0.438 0.313,0.198 10 false *1 2.979,1.198 3.292,1.396 0.313,0.198 10 false *2 0.51,1.042 0.823,1.24 0.313,0.198 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.


Hide 11821 8.INSTALL NO. 2 CAMSHAFT BEARING

Hide 11811 9.INSTALL NO. 1 CAMSHAFT BEARING

Hide 15678A 10.INSTALL OIL CONTROL VALVE FILTER

Hide 13512 11.INSTALL NO. 2 CAMSHAFT

HINT:

Perform inspection after repair after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft journals and camshaft housing sub-assembly.


b.

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.


c.

Install the No. 2 camshaft to the camshaft housing sub-assembly.


Hide 13511 12.INSTALL CAMSHAFT

HINT:

Perform inspection after repair after replacing the camshaft.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


b.

Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


c.

Install the camshaft to the camshaft housing sub-assembly.


Hide 13.INSTALL CAMSHAFT BEARING CAP

a.
A413676N01
0.531,0 0.698,0.208 0.167,0.208 10 false 1 1.021,0 1.188,0.208 0.167,0.208 10 false 2 1.625,0 1.792,0.208 0.167,0.208 10 false 3 2.25,0.01 2.417,0.219 0.167,0.208 10 false 4 2.813,0.01 2.979,0.219 0.167,0.208 10 false 5

Place the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps in their correct locations.


b.
A346308N01
1.844,1.604 2,1.802 0.156,0.198 10 true 1 2.427,1.594 2.583,1.792 0.156,0.198 10 true 3 3.042,1.573 3.198,1.771 0.156,0.198 10 true 7 2.677,0.094 2.833,0.292 0.156,0.198 10 true 8 2.167,0.073 2.323,0.271 0.156,0.198 10 true 4 1.563,0.094 1.719,0.292 0.156,0.198 10 true 2 0.979,0.083 1.135,0.281 0.156,0.198 10 true 6 0.167,0.146 0.417,0.365 0.25,0.219 10 false 10 0.177,1.906 0.531,2.104 0.354,0.198 10 true 11 1.323,1.573 1.479,1.771 0.156,0.198 10 true 5 0.083,0.917 0.333,1.135 0.25,0.219 10 false 9

Uniformly tighten the 11 bolts in several steps in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Make sure that the camshaft rotates smoothly after installing the camshaft bearing caps.



c.

Check the torque of each bolt again.


Hide 11103 14.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A407991C01
0.896,1.219 1.25,1.219 false 2.323,0.927 2.677,0.927 false 1.938,0.458 2.063,0.26 2.063,0.26 2.354,0.26 false 2.406,0.167 2.719,0.365 0.313,0.198 10 false *1 2.719,0.833 3.031,1.031 0.313,0.198 10 false *2 0.729,1.125 1.042,1.323 0.313,0.198 10 false *3 0.542,0.323 0.854,0.521 0.313,0.198 10 false *a 0.625,2.135 0.938,2.333 0.313,0.198 10 false *b
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Stem Cap
*3 Valve Lash Adjuster Assembly
*a Incorrect
*b Correct


Check that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.
A337899C03
1.635,1.177 1.979,0.458 1.979,0.458 2.188,0.458 true 1.24,0.177 1.552,0.333 0.313,0.156 10 false *b 1.51,2.708 1.823,2.865 0.313,0.156 10 false *c 2.229,0.375 2.542,0.531 0.313,0.156 10 false *a
*a Seal Packing
*b 2.5 to 3.5 mm (0.0984 to 0.138 in.)
*c 3.5 to 4.0 mm (0.138 to 0.157 in.)


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.




c.
A259156C12
1.115,1.219 1.729,1.823 1.729,1.823 2.365,1.198 true 1.656,1.844 1.833,2.021 0.177,0.177 10 false *c 0.917,0.219 1.094,0.396 0.177,0.177 10 false *a 2.271,0.219 2.448,0.396 0.177,0.177 10 false *b
*a Approximately 17°
*b Approximately 2°
*c Knock Pin


Position the knock pin of the camshaft and No. 2 camshaft as shown in the illustration.


d.
A346309N02
1.115,0.635 1.292,0.833 0.177,0.198 10 true 1 1.719,0.635 1.896,0.833 0.177,0.198 10 true 4 2.229,0.604 2.406,0.802 0.177,0.198 10 true 10 0.667,0.542 0.844,0.74 0.177,0.198 10 true 7 0.063,0.688 0.24,0.885 0.177,0.198 10 true 13 0.344,1.979 0.521,2.177 0.177,0.198 10 true 14 0.677,1.938 0.854,2.135 0.177,0.198 10 true 19 0.979,1.938 1.156,2.135 0.177,0.198 10 true 8 1.552,1.927 1.729,2.125 0.177,0.198 10 true 2 2.146,1.927 2.323,2.125 0.177,0.198 10 true 5 2.385,1.938 2.583,2.135 0.198,0.198 10 true 20 2.781,1.938 2.958,2.135 0.177,0.198 10 true 11 3.146,1.854 3.354,2.042 0.208,0.188 10 true 17 3.219,1.198 3.427,1.385 0.208,0.188 10 true 16 3.167,0.313 3.375,0.5 0.208,0.188 10 true 18 2.729,0.021 2.938,0.208 0.208,0.188 10 true 12 2.208,0 2.417,0.188 0.208,0.188 10 true 6 1.656,0.021 1.865,0.208 0.208,0.188 10 true 3 1.135,0.031 1.344,0.219 0.208,0.188 10 true 9 0.583,0.031 0.792,0.219 0.208,0.188 10 true 15

Install the camshaft housing sub-assembly, and then install the 20 bolts in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

After installation, if the seal packing has seeped out, wipe it off.




Hide 13050 15.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

Perform inspection after repair after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A285356C09
0.635,1.083 0.854,1.083 0.854,1.083 1.771,0.844 true 2.771,1.521 2.542,1.521 2.542,1.521 2.031,1.104 true 0.438,0.99 0.75,1.146 0.313,0.156 10 false *a 2.823,1.427 3.135,1.583 0.313,0.156 10 false *b
*a Knock Pin Hole
*b Alignment Mark


Check the camshaft timing gear assembly position. If the camshaft timing gear assembly is not set to the advanced position, release the lock pin and reset the camshaft timing gear assembly.


b.
A196901C81
1.979,0.625 1.854,0.625 1.854,0.625 1.635,0.906 true 1.25,0.208 1.125,0.208 1.125,0.208 0.698,0.771 true 1.281,0.125 1.458,0.302 0.177,0.177 10 false *a 2.021,0.542 2.188,0.719 0.167,0.177 10 false *b
*a Knock Pin Hole
*b Knock Pin


Align and fit the knock pin of the camshaft to the knock pin hole of the camshaft timing gear assembly.


c.
A196904C11
2.156,0.844 1.906,0.844 1.906,0.844 1.5,1.073 false 0.823,0.75 0.917,0.75 0.917,0.75 1.135,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 *1 1.802,0.531 2,0.698 0.198,0.167 10 *c 2.188,0.75 2.365,0.917 0.177,0.167 10 *2 1.74,2.021 1.938,2.177 0.198,0.156 10 *d 0.063,0.042 0.25,0.208 0.188,0.167 10 *a 0.063,1.833 0.26,2 0.198,0.167 10 *b
*1 Camshaft Timing Gear Assembly
*2 Camshaft Flange
*a Incorrect
*b Correct
*c Gap
*d No Gap


Check that there is no gap between the camshaft timing gear assembly and camshaft flange.


d.

Using a wrench to hold the hexagonal portion of the camshaft, install the camshaft timing gear assembly with the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear assembly.



HINT:

Perform inspection after repair after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13070A 16.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

HINT:

Perform inspection after repair after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Secure the No. 2 camshaft in a vise by clamping the hexagonal part between aluminum plates.

NOTICE:

Do not damage the No. 2 camshaft by tightening the vise excessively.



b.
A196902C35
1.896,0.656 1.771,0.656 1.771,0.656 1.594,0.927 false 1.229,0.177 1.104,0.177 1.104,0.177 0.667,0.802 true 1.938,0.552 2.125,0.719 0.188,0.167 10 false *b 1.281,0.104 1.448,0.271 0.167,0.167 10 false *a
*a Knock Pin Hole
*b Knock Pin


Align and fit the knock pin of the No. 2 camshaft to the knock pin hole of the camshaft timing exhaust gear assembly.


c.
A196904C92
2.146,0.854 1.896,0.854 1.896,0.854 1.5,1.073 false 0.823,0.76 0.917,0.76 0.917,0.76 1.125,0.979 false 0.604,0.667 0.781,0.823 0.177,0.156 10 false *1 0.156,0.146 0.333,0.313 0.177,0.167 10 false *a 0.146,1.927 0.344,2.083 0.198,0.156 10 false *b 1.802,0.542 2.115,0.74 0.313,0.198 10 false *c 2.198,0.771 2.375,0.927 0.177,0.156 10 false *2 1.771,2.031 1.948,2.188 0.177,0.156 10 false *d
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Flange
*a Incorrect
*b Correct
*c Gap
*d No Gap


Check that there is no gap between the camshaft timing exhaust gear assembly and camshaft flange.


d.
A407985C01
2.229,0.302 2.542,0.458 0.313,0.156 10 false *a 0.188,1.75 0.5,1.906 0.313,0.156 10 false *b
*a Hold
*b Turn


Using a wrench to hold the hexagonal portion of the No. 2 camshaft, install the camshaft timing exhaust gear assembly with the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear assembly.




Hide 17.ADD ENGINE OIL

a.
A198199

Add 50 cc (3.1 cu. in) of engine oil into the oil hole shown in the illustration.

NOTICE:
·

Engine oil must be added if the valve lash adjusters were removed.

·

Make sure that the low pressure chamber and oil paths of the valve lash adjusters are full of engine oil.




Hide 18.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.


b.
A285364C05
1.135,1.177 1.375,1.177 1.375,1.177 1.51,0.917 true 1.271,0.177 1.729,0.375 0.458,0.198 10 false 40° 0.958,1.094 1.156,1.25 0.198,0.156 10 true *1
*1 Crankshaft Pulley Key


Rotate the crankshaft 40° counterclockwise to position the crankshaft pulley key as shown in the illustration.


c.
A293511C11
1.781,2.823 1.979,2.823 1.979,2.823 2.604,3.104 true 0.458,2.865 0.583,2.865 0.583,2.865 0.792,3.104 true 0.292,2.771 0.604,2.927 0.313,0.156 10 false *c 0.969,0.698 1.281,0.854 0.313,0.156 10 false *a 2.448,0.823 2.76,0.979 0.313,0.156 10 false *b 1.594,2.729 1.906,2.885 0.313,0.156 10 false *c 3.021,3.677 3.219,3.854 0.198,0.177 10 false A 1.354,3.563 1.552,3.74 0.198,0.177 10 false A
*a Approximately 7°
*b Approximately 32°
*c Timing Mark


Check that the timing marks of the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.

HINT:

"A" is not a timing mark.



Hide 13561 19.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.
A196868

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13506 20.INSTALL CHAIN SUB-ASSEMBLY

a.

Place the chain sub-assembly onto the camshaft timing exhaust gear assembly, camshaft timing gear assembly and crankshaft timing sprocket.

HINT:
·

Make sure the paint mark of the chain sub-assembly is facing away from the engine assembly.

·

It is not necessary to install the chain sub-assembly to the teeth of the gears and sprocket.




b.
A196871C17
2.656,0.24 2.521,0.24 2.521,0.24 2.115,0.74 true 1.635,1.396 1.74,1.396 1.74,1.396 2.042,1.177 true 2.698,0.146 2.906,0.354 0.208,0.208 10 false *a 1.458,1.313 1.625,1.479 0.167,0.167 10 false *b
*a Paint Mark (Orange)
*b Timing Mark


Align the paint mark (orange) of the chain sub-assembly with the timing mark of the camshaft timing exhaust gear assembly and install the chain sub-assembly to the camshaft timing exhaust gear assembly.


c.
A196872C25
0.927,1.021 1.042,1.021 1.042,1.021 1.302,1.198 true 1.896,0.25 1.74,0.25 1.74,0.25 1.521,1.219 true 1.927,0.156 2.115,0.375 0.188,0.219 10 false *b 0.75,0.938 0.906,1.115 0.156,0.177 10 false *a
*a Paint Mark (Yellow)
*b Timing Mark


Align the paint mark (yellow) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket and install the chain sub-assembly to the crankshaft timing sprocket.


d.
A196873

Tie a string above the crankshaft timing sprocket so that the chain sub-assembly is secure.


e.
A196874C17
1.771,3.365 1.542,3.365 1.542,3.365 0.854,3.604 true 0.844,3.865 1.51,4.125 1.51,4.125 1.635,4.125 true 1.823,3.292 2.01,3.49 0.188,0.198 10 true *a 1.656,4.031 1.833,4.219 0.177,0.188 10 true *b
*a Paint Mark (Orange)
*b Timing Mark


Using the hexagonal portion of the camshaft, rotate the camshaft counterclockwise with a wrench, align the timing mark of the camshaft timing gear assembly with the paint mark (orange) of the chain sub-assembly, and install the chain sub-assembly to the camshaft timing gear assembly.

HINT:

Hold the camshaft in place with a wrench until the No. 1 chain tensioner assembly is installed.



f.
A196875

Remove the string above the crankshaft timing sprocket, rotate the crankshaft clockwise, and loosen the chain sub-assembly so that the chain tensioner slipper can be installed.

NOTICE:

Make sure the chain sub-assembly is securely installed.



Hide 13559 21.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13540 22.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A196877C03
0.469,0.979 0.552,0.979 0.552,0.979 1.302,0.979 true 0.302,0.896 0.615,1.094 0.313,0.198 10 false *a
*a Pin


Install a new gasket and the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Remove the pin from the stopper plate.


Hide 13566B 23.INSTALL TIMING CHAIN GUIDE

a.

Install the timing chain guide with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 24.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 12262 26.CONNECT NO. 2 VENTILATION HOSE

Hide 23250 27.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23291 28.INSTALL INJECTOR VIBRATION INSULATOR

Hide 23891 29.INSTALL FUEL DELIVERY SPACER

Hide 23814B 30.INSTALL FUEL DELIVERY PIPE

Hide 17650 31.INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 22271 32.INSTALL THROTTLE BODY GASKET

Hide 22030 33.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25051 34.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

Hide 17167 35.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11310 38.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY