Home › Power Source / Network › NETWORKING › NETWORK GATEWAY ECU › 2017.09–2017.12
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321447 NETWORK GATEWAY ECU A

NETWORKING  NETWORK GATEWAY ECU  INSTALLATION  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 89111 1.INSTALL CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for LHD, w/o ECU Integration Box RH)

a.

Engage the clamp.


b.

Connect the central gateway ECU (network gateway ECU) connector.


c.

Install the central gateway ECU (network gateway ECU) with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 89111 2.INSTALL CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for LHD, w/ ECU Integration Box RH)

a.
C386725

Engage the 2 claws to install the central gateway ECU (network gateway ECU).

NOTICE:

Make sure that the central gateway ECU (network gateway ECU) is securely installed.



Hide 82877 3.INSTALL ECU INTEGRATION BOX RH (for LHD, w/ ECU Integration Box RH)

a.

Install the ECU integration box RH with the bolt and nut.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)
Nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Engage the 2 clamps.


c.

Connect each connector.


Hide 55303B 4.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD, w/o Passenger Side Knee Airbag)

Hide 55303B 5.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD, w/ Passenger Side Knee Airbag)

Hide 73990 6.INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD, w/ Passenger Side Knee Airbag)

Hide 55607 7.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

Hide 55317A 8.INSTALL INSTRUMENT SIDE PANEL RH (for LHD)

Hide 62311B 9.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for LHD)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


Hide 62111A 10.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH (for LHD)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 67913 11.INSTALL FRONT DOOR SCUFF PLATE RH (for LHD)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 55476C 12.INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for LHD)

Hide 55012A 13.INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (for LHD)

Hide 55435B 14.INSTALL NO. 1 METER HOOD CLUSTER (for LHD)

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for LHD)

Hide 16. PERFORM DIAGNOSTIC SYSTEM CHECK (for LHD, w/ Passenger Side Knee Airbag)

Hide 17.INSPECT SRS WARNING LIGHT (for LHD, w/ Passenger Side Knee Airbag)

Hide 89111 18.INSTALL CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) (for RHD)

a.
C377924

Engage the 2 claws to install the central gateway ECU (network gateway ECU).

NOTICE:

Make sure that the central gateway ECU (network gateway ECU) is securely installed.



Hide 82877 19.INSTALL ECU INTEGRATION BOX RH (for RHD)

a.

Install the ECU integration box RH with the bolt and 2 nuts.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)
Nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Engage the clamp.


c.

Connect each connector.


Hide 55308B 20.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure as for LHD.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>INSTALLATION


Hide 73900 21.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)