Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › IGNITION SYSTEM
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0326371 IGNITION SYSTEM G

2GR-FKS ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A345137

To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fan when working in the engine compartment with the engine running or the engine switch on (IG).


PROCEDURE

Hide 1.PERFORM SPARK TEST

a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
NOTICE:

If any DTCs are output, perform troubleshooting in accordance with the procedure for each DTC.



f.

Turn the engine switch off.


g.

Remove the intake air surge tank assembly.

Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL


h.

Remove the 6 ignition coil assemblies and 6 spark plugs.

Click hereGeneral>MAINTENANCE>2GR-FKS SPARK PLUG>REMOVAL


i.
A408989C01
1.479,0.167 1.698,0.406 0.219,0.24 10 true *a 0.635,0.688 0.854,0.875 0.219,0.188 10 true *b 1.021,1.26 1.25,1.448 0.229,0.188 10 true *c 2.365,1.302 2.583,1.542 0.219,0.24 10 true *a
*a No. 5 Engine Wire Connector
*b No. 6 Engine Wire Connector
*c No. 7 Engine Wire Connector


Disconnect the 2 No. 5 engine wire connectors (for Port Injection).

NOTICE:

Perform this step in order to stop fuel injection to prevent damage to the catalyst due to unburned fuel.



j.

Disconnect the No. 6 engine wire connector and No. 7 engine wire connector (for Direct Injection).

NOTICE:

Perform this step in order to stop fuel injection to prevent damage to the catalyst due to unburned fuel.



k.

Install the spark plug to the ignition coil assembly, and then connect the ignition coil assembly connector.


l.

Ground the spark plug.


m.

Check that spark occurs at each spark plug while the engine is being cranked.

NOTICE:
·

Be sure to ground the spark plugs when checking them.

·

Do not crank the engine for more than 2 seconds.

·

If an ignition coil assembly or spark plug has been struck or dropped, replace it.



HINT:

If spark does not occur, perform the following procedure.



n.

Connect the No. 6 engine wire connector and No. 7 engine wire connector (for Direct Injection).


o.

Connect the 2 No. 5 engine wire connectors (for Port Injection).


p.

Install the 6 spark plugs and 6 ignition coil assemblies.

Click hereGeneral>MAINTENANCE>2GR-FKS SPARK PLUG>INSTALLATION


q.

Install the intake air surge tank assembly.

Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSTALLATION


r.

Turn the engine switch on (IG).


s.

Turn the GTS on.


t.

Enter the following menus: Powertrain / Engine / Trouble Codes.


u.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

v.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Hide 2.INSPECT IGNITION COIL ASSEMBLY AND SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Check that the ignition coil assembly connector is securely connected.

Result:
Result Action
NG Connect securely
OK Go to next step



b.

Perform a spark test on each ignition coil assembly.

i.

Replace the ignition coil assembly with a known good one.


ii.

Perform the spark test again.

Result:
Result Action
NG Go to next step
OK Replace ignition coil assembly


NOTICE:

If an ignition coil assembly or spark plug has been struck or dropped, replace it.




c.

Perform a spark test on each spark plug.

i.

Replace the spark plug with a known good one.


ii.

Perform the spark test again.

Result:
Result Action
NG Inspect the ignition system
(Click here)
OK Replace spark plug


NOTICE:

If an ignition coil assembly or spark plug has been struck or dropped, replace it.




d.

Connect the No. 6 engine wire connector and No. 7 engine wire connector (for Direct Injection).


e.

Connect the 2 No. 5 engine wire connectors (for Port Injection).


f.

Install the 6 spark plugs and 6 ignition coil assemblies.

Click hereGeneral>MAINTENANCE>2GR-FKS SPARK PLUG>INSTALLATION


g.

Install the intake air surge tank assembly.

Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSTALLATION


h.

Turn the engine switch on (IG).


i.

Turn the GTS on.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes.


k.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

l.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Hide 19100P 3.INSPECT SPARK PLUG

NOTICE:
·

Do not damage the iridium tip and platinum tip.

·

Check the iridium tip visually since the iridium tip may be damaged.

·

Never attempt to adjust the electrode gap of a used spark plug.

·

Replace with new spark plugs if extremely dirty due to sludge, etc.

·

Replace with new spark plugs if damaged at all.

·

Replace with a new spark plug if it has been struck or dropped.

·

When replacing with a new spark plug, do not remove the cap for protecting the spark plug tip until it is installed to the engine.



HINT:

Perform "Inspection After Repair" after replacing a spark plug.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
I039522C34
0.708,1.969 1.094,1.917 false 0.563,1.875 0.74,2.042 0.177,0.167 10 false *a
*a Body Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher


HINT:
·

If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

·

If a megohmmeter is not available, perform the following simple inspection instead.





b.

Alternative inspection method.

i.

Start the engine.

NOTICE:

Do not perform this step when any of the following DTCs are output: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500, P030600 (Cylinder Misfire Detected).



ii.

Quickly accelerate the engine to 4000 rpm 5 times.

NOTICE:

Do not perform this step when any of the following DTCs are output: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500, P030600 (Cylinder Misfire Detected).



iii.

Remove the spark plug.

Click hereGeneral>MAINTENANCE>2GR-FKS SPARK PLUG>REMOVAL


iv.

Visually check the spark plug.

HINT:

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.




c.

Check the spark plug for any damage to its threads and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO FK20HBR8



d.
A155866C01
1.198,1.323 2,1.323 false 1.208,1.479 1.438,1.75 1.438,1.75 1.979,1.75 false 0.448,1.667 0.76,1.823 0.313,0.156 10 false *a 2.073,1.24 2.385,1.396 0.313,0.156 10 false *b 2.073,1.667 2.385,1.823 0.313,0.156 10 false *c
*a Spark Plug Electrode Gap
*b Iridium Tip
*c Platinum Tip


Check the spark plug electrode gap.

Maximum Electrode Gap for Used Spark Plug:

1.1 mm (0.0433 in.)


NOTICE:

Never attempt to adjust the electrode gap of a used spark plug.


If the electrode gap is more than the maximum, replace the spark plug.

Standard Electrode Gap for New Spark Plug:

0.7 to 0.8 mm (0.0276 to 0.0315 in.)



e.

Install the spark plug.

Click hereGeneral>MAINTENANCE>2GR-FKS SPARK PLUG>INSTALLATION


Hide 4.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION