Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › AIR FUEL RATIO SENSOR
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0326389 AIR FUEL RATIO SENSOR A

2GR-FKS ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


PROCEDURE

Hide 89467C 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 1)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A408213C01
1.25,1.313 1.729,1.313 true 1.781,0.125 2.031,0.344 0.25,0.219 10 true *a 1.76,1.219 2.135,1.438 0.375,0.219 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold assembly RH (TWC: Front Catalyst).

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




b.

Engage the 2 wire harness clamps.


c.

Connect the air fuel ratio sensor connector.


Hide 89467B 2.INSTALL AIR FUEL RATIO SENSOR (for Bank 2)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A408210C01
1.688,1.906 1.688,1.635 true 1.615,0.823 1.833,1 0.219,0.177 10 true *a 1.573,1.917 1.927,2.115 0.354,0.198 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the air fuel ratio sensor to the exhaust manifold assembly LH (TWC: Front Catalyst).

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the air fuel ratio sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




b.

Connect the air fuel ratio sensor connector.


c.

Engage the wire harness clamp.


Hide 11209 3.INSTALL V-BANK COVER SUB-ASSEMBLY

Hide 5.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing an air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION