Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY
RM33A0E _51 Engine / Hybrid System _065333 2GR-FKS ENGINE MECHANICAL _0327370 ENGINE ASSEMBLY A

2GR-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>INSTALLATION

Hide 12304 2.INSTALL ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.


a.
A415553N01
2.323,0.667 2.479,0.865 0.156,0.198 10 true A 3.198,2.271 3.375,2.479 0.177,0.208 10 true B 0.563,1.302 0.719,1.5 0.156,0.198 10 true C 1.396,0.51 1.552,0.708 0.156,0.198 10 true D

Temporarily tighten the bolt (A), and then fully tighten the 4 bolts in the order of (B), (C), (D) and (A).

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Make sure that there is no gap between the engine mounting bracket sub-assembly LH and vehicle body before tightening the bolts.



Hide 12341 3.INSTALL ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A415554N01
0.625,0.833 0.781,1.031 0.156,0.198 10 true A 2.75,0.74 2.906,0.938 0.156,0.198 10 true B

Install the engine mounting spacer to the vehicle body with the 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).



Hide 12305 4.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A401622E01
0.74,1.146 0.896,1.344 0.156,0.198 10 true A 2.604,1.208 2.76,1.406 0.156,0.198 10 true B 2.354,0.24 2.51,0.438 0.156,0.198 10 true C

Install the engine mounting insulator sub-assembly RH to the engine mounting spacer and vehicle body with the nut and 2 bolts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A), and then fully tighten the 2 bolts and nut in the order of (B), (A) and (C).



b.

Engage the clamp.


c.

Connect the No. 1 bond cable to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


d.

Install the bracket to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
A415563N01
1.021,1.51 1.177,1.708 0.156,0.198 10 true 1 1.563,0.167 1.719,0.365 0.156,0.198 10 true 2

Install the radiator reserve tank assembly with the bolt and nut in the order shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


f.

Engage the clamp.


Hide 6.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 19315 7.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 32101 8.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 12371A 11.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ACTIVE CONTROL ENGINE MOUNT (for Rear Side)>INSTALLATION

Hide 12361A 12.INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.

Install the front engine mounting insulator to the front frame assembly with the 3 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 51100G 13.INSTALL FRONT FRAME ASSEMBLY

a.

Install the rear engine mounting insulator to the front frame assembly with the 4 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


b.

Install the front engine mounting insulator to the front engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 82121 15.INSTALL ENGINE WIRE

a.

Connect all connectors and clamps, and install the engine wire to the engine assembly with transaxle.


Hide 28100 19.INSTALL STARTER ASSEMBLY

Hide 21.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:

Perform Inspection After Repair after replacing the engine assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front frame assembly level, set an engine lifter underneath the engine assembly with transaxle and front frame assembly.

NOTICE:
·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.
A399871C02
1.333,2.177 1.49,2.375 0.156,0.198 10 true A 1.333,2.417 1.49,2.615 0.156,0.198 10 true A 1.938,2.177 2.094,2.375 0.156,0.198 10 true A 1.938,2.396 2.094,2.594 0.156,0.198 10 true A 0.938,0.344 1.094,0.542 0.156,0.198 10 true B 2.302,0.385 2.458,0.583 0.156,0.198 10 true B 1.219,2.719 1.375,2.917 0.156,0.198 10 true C 2.063,2.708 2.219,2.906 0.156,0.198 10 true C 0.698,3.719 0.854,3.917 0.156,0.198 10 true E 2.573,3.74 2.729,3.938 0.156,0.198 10 true E 0.771,4.448 0.927,4.646 0.156,0.198 10 true D 2.521,4.458 2.677,4.656 0.156,0.198 10 true D
V100135

Bolt
V100136

Nut


Install the front bumper extension sub-assembly RH and front bumper extension sub-assembly LH to the front frame assembly and vehicle body with the 8 bolts.

Torque:
Bolt (A) : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
Bolt (B) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (C) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)


d.

Install the front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH to the front frame assembly and vehicle body with the 4 bolts and 2 nuts.

Torque:
Bolt (D) : 17.5 N*m (178 kgf*cm, 13 ft.*lbf)
Bolt (E) : 135 N*m (1377 kgf*cm, 100 ft.*lbf)
Nut : 17.5 N*m (178 kgf*cm, 13 ft.*lbf)


e.

Install the engine mounting insulator LH to the engine mounting bracket sub-assembly LH with the bolt and nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


f.

Install the engine mounting insulator sub-assembly RH to the front No. 1 engine mounting bracket LH with the 3 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 42 N*m (428 kgf*cm, 31 ft.*lbf)


g.

Install the No. 2 engine mounting stay RH with the bolt and 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 32101A 22.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 11361J 23.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17571 24.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Upper Side)

a.

Install the No. 1 exhaust pipe support bracket to the oil pan sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 45220 27.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 82284 28.CONNECT EARTH WIRE

a.

Connect the earth wire to the vehicle body with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82121 29.CONNECT ENGINE WIRE

a.

Engage the 2 clamps and connect the engine wire to the vehicle body.


b.

Connect the engine wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Engage the 2 clamps.


d.

Engage the claw and connect the engine wire to the engine room relay block and junction block assembly.


e.

Install the nut to the engine room relay block and junction block assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.

Connect the 4 connectors to the engine room relay block and junction block assembly.


g.

Install the No. 2 relay block cover to the engine room relay block and junction block assembly.


Hide 88704 30.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 31.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

Hide 23801F 32.CONNECT NO. 1 FUEL HOSE

a.

Install the No. 1 fuel hose with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the No. 1 fuel hose (for Port Injection).

i.

Connect the No. 1 fuel hose to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



c.

Connect the No. 1 fuel hose (for Direct Injection).

i.

Connect the No. 1 fuel hose to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



d.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


e.

Engage the 2 claws to install the No. 2 fuel pipe clamp.


Hide 87246 33.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose to the heater water pipe and slide the clip to secure it.


Hide 87245 34.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose to the water outlet and slide the clip to secure it.


b.

Engage the clamp.


Hide 35.CONNECT RADIATOR HOSE SUB-ASSEMBLY

a.

Connect the radiator hose sub-assembly to the water outlet and slide the clip to secure it.


b.

Install the radiator hose sub-assembly to the engine assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 16572D 36.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.


Hide 44773F 37.CONNECT UNION TO CHECK VALVE HOSE

a.

Connect the union to check valve hose to the brake booster assembly and slide the clip to secure it.


Hide 23826 38.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve and slide the clip to secure it.


Hide 33820B 39.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


b.
C378151C01
0.74,2.042 1.052,2.198 0.313,0.156 10 false *a 2.146,2.052 2.458,2.208 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.



Hide 74404A 40.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly with the 3 bolts.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


b.

Engage the 5 clamps to the battery clamp sub-assembly.


Hide 82111 42.CONNECT ENGINE ROOM MAIN WIRE

a.

Connect the engine wire with engine room main wire to the positive (+) battery terminal with the nut.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


Hide 44.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A408246C01
2.052,0.604 1.854,0.604 1.854,0.604 1.854,0.844 true 2.125,0.667 2.354,0.865 2.354,0.865 2.333,0.604 true 0.844,2.521 0.844,2.146 0.844,2.146 1.271,2.146 true 0.229,2.313 0.229,2.917 true 1.521,0.229 1.833,0.427 0.313,0.198 10 false *d 1.781,0.844 2.094,1.042 0.313,0.198 10 true *c 2.333,0.063 2.646,0.26 0.313,0.198 10 false *d 2.333,0.885 2.646,1.083 0.313,0.198 10 false *e 1.302,2.083 1.615,2.281 0.313,0.198 10 false *b 0.167,2.948 0.479,3.146 0.313,0.198 10 false *a
*a Protrusion
*b Cutout
*c Hose Clamp End
*d 2.0 mm (0.0787 in.)
*e Paint Mark


Install the air cleaner assembly with air cleaner hose to the throttle body with motor assembly.

NOTICE:

Align the cutout of the air cleaner hose assembly with the protrusion of the throttle body with motor assembly.



b.

Tighten the hose clamp in the position shown in the illustration.

NOTICE:

Make sure that the end of the hose clamp is positioned as shown in the illustration.



c.
A408245C01
2,4.115 2.531,4.115 true 0.594,3.948 1.031,3.948 true 1.333,3.563 1.469,4.021 true 0.375,3.865 0.625,4.104 0.25,0.24 10 true *a 1.365,4.042 1.615,4.281 0.25,0.24 10 true *a 2.542,4.021 2.792,4.26 0.25,0.24 10 true *a
*a Air Cleaner Support


Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports as shown in the illustration.

NOTICE:
·

Insert the 3 pins of the air cleaner assembly into the 3 air cleaner supports at the same time.

·

Check that the pins are securely inserted into air cleaner supports.




d.

Engage the vacuum hose to the air cleaner hose.


e.

Engage the 3 wire harness clamps.


f.

Connect the mass air flow meter sub-assembly connector.


g.
A408247C01
2.25,0.792 2.833,0.792 true 1.51,1.219 1.51,1.688 true 0.833,0.917 0.938,0.604 0.938,0.604 1.083,0.604 true 0.594,0.594 0.594,0.427 0.594,0.427 0.333,0.427 false 2.875,0.708 3.188,0.906 0.313,0.198 10 true *1 1.448,1.729 1.76,1.927 0.313,0.198 10 true *2 0.771,0.26 1.083,0.458 0.313,0.198 10 true *a 0.083,0.906 0.302,1.104 0.219,0.198 10 false *c 1.115,0.542 1.427,0.74 0.313,0.198 10 false *b 0.177,0.365 0.49,0.563 0.313,0.198 10 false *d
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Ventilation Hose
*a Top
*b Paint Mark
*c Rear of Vehicle
*d 180° (Claw of Clip Location)


Connect the No. 2 ventilation hose to the air cleaner hose and slide the clip to secure it.

NOTICE:

Make sure that the condition of the clip is as shown in the illustration.



h.

Engage the 2 clamps to connect the No. 1 fuel vapor feed hose to the air cleaner hose.


Hide 17750A 45.INSTALL INLET AIR CLEANER ASSEMBLY

a.
A399875E01
0.344,0.958 0.5,1.156 0.156,0.198 10 true 1 2.406,1.698 2.563,1.896 0.156,0.198 10 true 2

Install the inlet air cleaner assembly with the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 11209 46.INSTALL V-BANK COVER SUB-ASSEMBLY

a.
A399876N01
1.854,1.594 2.01,1.792 0.156,0.198 10 true 1 1.021,0.969 1.177,1.167 0.156,0.198 10 true 2 0.281,1.708 0.438,1.906 0.156,0.198 10 true 1 1.76,1 1.917,1.198 0.156,0.198 10 true 2

Engage the 4 clips in the order shown in the illustration to install the V-bank cover sub-assembly.

NOTICE:
·

Make sure that the clips are engaged securely.

·

Do not subject the clips to shock or apply excessive force to the clips when engaging them or they may be damaged.

·

If the clips are not engaged in the order shown in the illustration, the V-bank cover sub-assembly may be damaged.




Hide 47.INSPECT VACUUM HOSES

a.

Inspect the vacuum hoses.

A408400


Hide 48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 50.ADD ENGINE COOLANT

Hide 52.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 56.INSPECT FOR ENGINE OIL LEAK

Hide 57.INSPECT FOR COOLANT LEAK

Hide 62.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 52618 63.INSTALL FRONT LOWER BUMPER ABSORBER

a.

Engage the 2 claws to the front lower bumper absorber.


b.

Install the 4 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 52119A 64.INSTALL FRONT BUMPER COVER

Hide 53737B 65.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 2 screws and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53736 66.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 2 screws and clip.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 51441 67.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the bolt, 6 screws and 2 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53852K 68.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

a.

Install the front wheel opening extension pad LH with the 3 screws.


Hide 53851M 69.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

a.

Install the front wheel opening extension pad RH with the 3 screws.


Hide 70.INSTALL FRONT WHEELS

Hide 71.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 72.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT