Home › Drivetrain › U760E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2017.09–2021.02
RM33A0E _52 Drivetrain _065350 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0322783 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0748  Pressure Control Solenoid "A" Electrical  


DESCRIPTION

Changing from 1st to 6th gear is performed by the ECM turning solenoid (SL1, SL2, SL3, SL4 and SL) valves on and off. If an open or short occurs in any of the solenoid valve circuits, the ECM controls the remaining normal solenoid valves to allow the vehicle to be driven.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0748 Pressure Control Solenoid "A" Electrical While driving so that gear changes occur, an open or short is detected in the solenoid (SL1) valve circuit for 1 second (1-trip detection logic).
·

Wiring harness connector

·

Open or short in solenoid (SL1) valve circuit

·

Solenoid (SL1) valve

·

Transmission wire

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short in the solenoid (SL1) valve circuit. The ECM commands gear shifts by turning the solenoid valves on or off. When there is an open or short in any of the solenoid valve circuits, the ECM detects the problem, illuminates the MIL and stores a DTC. The ECM also performs the fail-safe function and turns the other normal solenoid valves on or off. (In the case of an open or short, the ECM stops sending current to the circuit.)

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

While driving and shifting between 4th and 5th gear, if the ECM detects an open or short in the solenoid (SL1) valve circuit, the ECM determines there is a malfunction.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for 2 minutes or more.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0748.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C314405E55
1.177,2.969 3.031,3.479 1.854,0.51 10 false Transmission Wire 3.031,2.969 4.052,3.365 1.021,0.396 10 false Wiring Harness Connector 5.583,2.958 6.042,3.156 0.458,0.198 10 false C58 5.594,3.135 6.052,3.333 0.458,0.198 10 false ECM 1.542,1.552 2.469,2 0.927,0.448 10 false Solenoid (SL1) Valve 2.313,0.99 2.927,1.188 0.615,0.198 10 false SL1+ 3.104,0.99 3.719,1.188 0.615,0.198 10 false SL1+ 3.594,0.99 4.208,1.188 0.615,0.198 10 false SL1+ 5.063,1 5.677,1.198 0.615,0.198 10 false SL1+ 5.073,1.99 5.688,2.188 0.615,0.198 10 false SL1- 3.615,1.99 4.229,2.188 0.615,0.198 10 false SL1- 3.104,1.99 3.719,2.188 0.615,0.198 10 false SL1- 2.344,1.99 2.958,2.188 0.615,0.198 10 false SL1- 2.823,1.115 2.979,1.313 0.156,0.198 10 false A 2.823,2.115 2.979,2.313 0.156,0.198 10 false A 4.021,1.104 4.333,1.302 0.313,0.198 10 false C54 4.021,2.104 4.333,2.302 0.313,0.198 10 false C54 4.813,1 5.125,1.198 0.313,0.198 10 false 11 4.813,1.99 5.125,2.188 0.313,0.198 10 false 10 4.052,1.906 4.365,2.104 0.313,0.198 10 false 16 4.063,0.906 4.375,1.104 0.313,0.198 10 false 17 2.792,0.917 3.104,1.115 0.313,0.198 10 false 14 2.781,1.927 3.094,2.125 0.313,0.198 10 false 13 5.625,0.76 6,1.052 0.375,0.292 10 false 12 V 1.25,1.313 1.406,1.51 0.156,0.198 10 false 2 1.25,1.948 1.406,2.146 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

The following table shows normal operation of the solenoid (SL1) valve when the shift lever is in D:

ECM commanded gear 1st 2nd 3rd 4th 5th 6th
Solenoid (SL1) valve ON ON ON ON OFF OFF


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SOLENOID (SL1) VALVE CIRCUIT)
a.

Disconnect the C58 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-11 (SL1+) - C58-10 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
C58-11 (SL1+) - Body ground and other terminals Always 10 kΩ or higher
C58-10 (SL1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
a.

Disconnect the C54 wiring harness connector connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-11 (SL1+) - C54-17 (SL1+) Always Below 1 Ω
C58-10 (SL1-) - C54-16 (SL1-) Always Below 1 Ω
C58-11 (SL1+) or C54-17 (SL1+) - Body ground and other terminals Always 10 kΩ or higher
C58-10 (SL1-) or C54-16 (SL1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (SOLENOID (SL1) VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (SOLENOID (SL1) VALVE)
a.
C370673C03
0.5,1.083 0.917,1.333 0.417,0.25 1.24,1.979 1.656,1.313 true 2.208,1.969 1.792,1.302 true 0.333,0.344 0.646,0.5 0.313,0.156 10 false *a 0.875,1.906 1.49,2.104 0.615,0.198 10 false SL1+ 2.26,1.906 2.875,2.104 0.615,0.198 10 false SL1- 0.667,1.115 0.823,1.313 0.156,0.198 10 false A
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-14 (SL1+) - A-13 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
A-14 (SL1+) - Body ground and other terminals Always 10 kΩ or higher
A-13 (SL1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SOLENOID (SL1) VALVE
4.INSPECT SOLENOID (SL1) VALVE
a.
C201747C03
1.5,0.854 0.646,0.625 false 1.781,0.844 2.479,0.604 false 1.51,3.135 0.656,2.906 false 1.781,3.115 2.479,2.875 false 0.49,0.521 0.667,0.719 0.177,0.198 10 1 2.531,0.5 2.708,0.698 0.177,0.198 10 2 1.198,4.208 1.406,4.417 0.208,0.208 10 (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 (+) 0.49,2.771 0.667,2.969 0.177,0.198 10 1 2.531,2.771 2.708,2.969 0.177,0.198 10 2 0.135,0.083 0.354,0.292 0.219,0.208 10 *1
*1 Solenoid (SL1) Valve


Remove the solenoid (SL1) valve.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG