Changing from 1st to 6th gear is performed by the ECM turning solenoid (SL1, SL2, SL3, SL4 and SL) valves on and off. If an open or short occurs in any of the solenoid valve circuits, the ECM controls the remaining normal solenoid valves to allow the vehicle to be driven.
Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0798 | Pressure Control Solenoid "C" Electrical | While driving so that gear changes occur, an open or short is detected in the solenoid (SL3) valve circuit for 1 second (1-trip detection logic). | ·
Wiring harness connector ·
Open or short in solenoid (SL3) valve circuit ·
Solenoid (SL3) valve ·
Transmission wire ·
ECM |
Comes on | DTC stored |
This DTC indicates an open or short in the solenoid (SL3) valve circuit. The ECM commands gear shifts by turning the solenoid valves on or off. When there is an open or short in any of the solenoid valve circuits, the ECM detects the problem, illuminates the MIL and stores a DTC. The ECM also performs the fail-safe function and turns the other normal solenoid valves on or off. (In the case of an open or short, the ECM stops sending current to the circuit.)
Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Perform the D Position Shift Test inspection in Road Test.
Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0798.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
The following table shows normal operation of the solenoid (SL3) valve when the shift lever is in D:
| ECM commanded gear | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Solenoid (SL3) valve | OFF | ON | OFF | OFF | OFF | ON |
Disconnect the C58 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C58-7 (SL3+) - C58-6 (SL3-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| C58-7 (SL3+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C58-6 (SL3-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C54 wiring harness connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C58-7 (SL3+) - C54-19 (SL3+) | Always | Below 1 Ω |
| C58-6 (SL3-) - C54-18 (SL3-) | Always | Below 1 Ω |
| C58-7 (SL3+) or C54-19 (SL3+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C58-6 (SL3-) or C54-18 (SL3-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Transmission Wire) |
Remove the wiring harness connector.
Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (SL3+) - A-15 (SL3-) | 20°C (68°F) | 5.0 to 5.6 Ω |
| A-16 (SL3+) - Body ground | Always | 10 kΩ or higher |
| A-15 (SL3-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>COMPONENTS
NG
| *1 | Solenoid (SL3) Valve |
Remove the solenoid (SL3) valve.
Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
| Proceed to |
|---|
| OK |
| NG |
OK
NG