Home › General › MAINTENANCE › U760E AUTOMATIC TRANSAXLE FLUID › 2017.09–2021.02
RM33A0E _V1 General _065356 MAINTENANCE _0327046 U760E AUTOMATIC TRANSAXLE FLUID A

MAINTENANCE  U760E AUTOMATIC TRANSAXLE FLUID  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transaxle fluid replacement are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)

PROCEDURE

Hide 53737B 1.REMOVE FRONT FENDER APRON SEAL LH

Hide 2.REPLACE AUTOMATIC TRANSAXLE FLUID

a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear and side to side of the vehicle is within +/- 1°).



b.
C378107

Remove the refill plug and gasket from the rear transaxle cover sub-assembly. [#2]


c.
C378108

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly. [#3]


d.
C378109C01
0.719,1.156 0.844,1.156 false 0.865,1.042 1.177,1.24 0.313,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly and drain the automatic transaxle fluid. [#4]


e.
C378110

Measure the amount of automatic transaxle fluid drained. [#5]

HINT:

Add the same amount of automatic transaxle fluid in step [#8].



f.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly. [#6]

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


g.
C378108

Using a 6 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly. [#7]

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



h.
C378111

Add automatic transaxle fluid to the refill hole using the same amount of automatic transaxle fluid drained in step [#5]. [#8]

NOTICE:

Use Toyota Genuine ATF WS.



i.
C378107

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage. [#9]

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



j.

Lower the vehicle. [#10]


k.

Start the engine. [#11]


l.

Slowly move the shift lever from P to D, and then back to P. [#12]

HINT:
·

Slowly move the shift lever to circulate the automatic transaxle fluid through each part of the automatic transaxle assembly.

·

Keep the shift lever in each position for approximately 3 seconds.




m.

Allow the engine to idle for 30 seconds to warm it up. [#13]


n.

Turn the ignition switch off. [#14]


o.

Repeat steps [#1] to [#14].


p.

Repeat steps [#1] to [#10].


Hide 3.ADD SPECIFIED AMOUNT OF AUTOMATIC TRANSAXLE FLUID

Hide 4.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Using the GTS)

Hide 5.ADJUST AUTOMATIC TRANSAXLE FLUID TEMPERATURE (when Not Using the GTS)

Hide 53737B 8.INSTALL FRONT FENDER APRON SEAL LH

Hide 9. ATF THERMAL DEGRADATION ESTIMATE RESET

NOTICE:

Perform ATF Thermal Degradation Estimate Reset if approximately 50% or more of the ATF has been replaced during a repair or a similar operation.

Click hereDrivetrain>U760E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION