The main body ECU (multiplex network body ECU) controls the operation of the following lights:
Front Door Inside Handle Illumination Light LH (No. 1 Interior Illumination Light Assembly LH)
Front Door Inside Handle Illumination Light RH (No. 1 Interior Illumination Light Assembly RH)
Rear Door Inside Handle Illumination Light LH (No. 2 Interior Illumination Light Assembly LH)*
Rear Door Inside Handle Illumination Light RH (No. 2 Interior Illumination Light Assembly RH)*
*: w/ Rear Door Inside Handle Illumination Light
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*2
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*1: w/ Smart Entry and Start System
*2: w/ Door Control Battery
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Interior Illumination Light2 | ·
Front door inside handle illumination light (No. 1 interior illumination light assembly) ·
Rear door inside handle illumination light (No. 2 interior illumination light assembly)* |
OFF or ON | Preconditions for using the Active Test to check dimmer controlled illumination:
·
Ignition switch ON ·
Shift lever is in any position other than P |
*: w/ Rear Door Inside Handle Illumination Light
| Tester Display |
|---|
| Interior Illumination Light2 |
Inside handle illumination lights come on.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Front door inside handle illumination light LH does not come on) | B |
| NG (Front door inside handle illumination light RH does not come on) | C |
| NG (Rear door inside handle illumination light LH does not come on)* | D |
| NG (Rear door inside handle illumination light RH does not come on)* | E |
| NG (All inside handle illumination lights do not come on) | F |
*: w/ Rear Door Inside Handle Illumination Light
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
E
F
Remove the front door inside handle illumination light LH (No. 1 interior illumination light assembly LH).
Click hereVehicle Interior>LIGHTING (INT)>INSIDE HANDLE LIGHT (for Front Side)>REMOVAL
Inspect the front door inside handle illumination light LH (No. 1 interior illumination light assembly LH).
Click hereVehicle Interior>LIGHTING (INT)>INSIDE HANDLE LIGHT (for Front Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-26 - O14-2 (+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K53 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O14-1 (-) - K53-21 (LED2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the front door inside handle illumination light RH (No. 1 interior illumination light assembly RH).
Click hereVehicle Interior>LIGHTING (INT)>INSIDE HANDLE LIGHT (for Front Side)>REMOVAL
Inspect the front door inside handle illumination light RH (No. 1 interior illumination light assembly RH).
Click hereVehicle Interior>LIGHTING (INT)>INSIDE HANDLE LIGHT (for Front Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-26 - N14-2 (+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K53 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N14-1 (-) - K53-21 (LED2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the rear door inside handle illumination light LH (No. 2 interior illumination light assembly LH).
Click hereVehicle Interior>LIGHTING (INT)>INSIDE HANDLE LIGHT (for Rear Side)>REMOVAL
Inspect the rear door inside handle illumination light LH (No. 2 interior illumination light assembly LH).
Click hereVehicle Interior>LIGHTING (INT)>INSIDE HANDLE LIGHT (for Rear Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-26 - Q4-2 (+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K53 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q4-1 (-) - K53-21 (LED2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the rear door inside handle illumination light RH (No. 2 interior illumination light assembly RH).
Click hereVehicle Interior>LIGHTING (INT)>INSIDE HANDLE LIGHT (for Rear Side)>REMOVAL
Inspect the rear door inside handle illumination light RH (No. 2 interior illumination light assembly RH).
Click hereVehicle Interior>LIGHTING (INT)>INSIDE HANDLE LIGHT (for Rear Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-26 - P4-2 (+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K53 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P4-1 (-) - K53-21 (LED2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the 3F*1 or 3G*2 instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3F-1 - Body ground*1 | Always | 11 to 14 V |
| 3G-1 - Body ground*2 | Always | 11 to 14 V |
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD | *B | for RHD |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-26 - 3F-1*1 | Always | Below 1 Ω |
| 3B-26 - 3G-1*2 | Always | Below 1 Ω |
*1: for LHD
*2: for RHD
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O14 front door inside handle illumination light LH (No. 1 interior illumination light assembly LH) connector.
Disconnect the N14 front door inside handle illumination light RH (No. 1 interior illumination light assembly RH) connector.
Disconnect the Q4 rear door inside handle illumination light LH (No. 2 interior illumination light assembly LH) connector.*
Disconnect the P4 rear door inside handle illumination light RH (No. 2 interior illumination light assembly RH) connector.*
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-26 - O14-2 (+) | Always | Below 1 Ω |
| 3B-26 - N14-2 (+) | Always | Below 1 Ω |
| 3B-26 - Q4-2 (+)* | Always | Below 1 Ω |
| 3B-26 - P4-2 (+)* | Always | Below 1 Ω |
| 3B-26, O14-2 (+), N14-2 (+), Q4-2 (+)* or P4-2 (+)* - Body ground | Always | 10 kΩ or higher |
*: w/ Rear Door Inside Handle Illumination Light
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K53 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O14-1 (-) - K53-21 (LED2) | Always | Below 1 Ω |
| N14-1 (-) - K53-21 (LED2) | Always | Below 1 Ω |
| Q4-1 (-) - K53-21 (LED2)* | Always | Below 1 Ω |
| P4-1 (-) - K53-21 (LED2)* | Always | Below 1 Ω |
| O14-1 (-), N14-1 (-), Q4-1 (-)*, P4-1 (-)* or K53-21 (LED2) - Body ground | Always | 10 kΩ or higher |
*: w/ Rear Door Inside Handle Illumination Light
| Proceed to |
|---|
| OK |
| NG |
OK
NG