Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 2AR-FE LH Side) › 2017.09–2017.12
RM33A0E _53 Suspension _065361 FRONT SUSPENSION _0327160 FRONT LOWER SUSPENSION ARM(for 2AR-FE LH Side) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 2AR-FE LH Side)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front lower No. 1 suspension arm sub-assembly LH removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system for Initialization:(Click here)
for Calibration:(Click here)
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)

PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 53852K 2.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 3.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53737B 5.REMOVE FRONT FENDER APRON SEAL LH

Hide 17700 6.REMOVE AIR CLEANER ASSEMBLY

Hide 7.REMOVE BATTERY

Hide 74404A 8.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 48069 9.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C373242

Remove the bolt and 2 nuts and separate the front lower No. 1 suspension arm sub-assembly LH from the front lower ball joint assembly LH.


Hide 12361A 10.SEPARATE FRONT ENGINE MOUNTING INSULATOR

a.
C373236

Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.


Hide 48069 11.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C373240C01
2.323,0.823 2.719,0.323 2.719,0.323 2.844,0.323 true 2.094,1.615 2.531,2.188 2.531,2.188 2.646,2.188 true 2.688,2.104 3,2.26 0.313,0.156 10 false *a 2.885,0.24 3.094,0.396 0.208,0.156 10 true *b
*a Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Using a jack and wooden block, support the engine assembly with transaxle at the position shown in the illustration.

NOTICE:
·

Do not position the wooden block under the oil pan.

·

Ensure that the jack and wooden block are stable.




b.
C373239

Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.


c.

While ensuring that there is no interference from the components surrounding the engine, tilt the engine assembly with transaxle to a position that allows the front lower No. 1 suspension arm sub-assembly LH bolt.

NOTICE:
·

Do not damage the components surrounding the engine assembly with transaxle.

·

Tilt the engine assembly with transaxle as little as possible.

·

Keep the engine assembly with transaxle supported until installation of the front lower No. 1 suspension arm sub-assembly LH.




d.
C373243

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly LH.