Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1330  Open in Front Speed Sensor RH  C1331  Open in Front Speed Sensor LH  C1332  Open in Rear Speed Sensor RH  C1333  Open in Rear Speed Sensor LH  C1464  Front Speed Sensor RH  C1465  Front Speed Sensor LH  C1466  Rear Speed Sensor RH  C1467  Rear Speed Sensor LH  


DESCRIPTION

Each speed sensor detects wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS control.

HINT:

The output voltage values shown below are for when the vehicle wire harnesses are connected to the skid control ECU (brake actuator assembly) and the speed sensors.


for Front
C223506E20
1.281,1.063 1.281,0.708 1.281,0.708 1.073,0.708 false 0.156,0.604 1.344,0.917 1.188,0.313 10 false Speed Sensor 4.938,1.917 5.781,2.104 0.844,0.188 10 false High speed 4.01,1.917 4.792,2.104 0.781,0.188 10 false Low speed 6.052,1.156 6.51,1.427 0.458,0.271 10 false 0.3 V 6.052,1.49 6.542,1.813 0.49,0.323 10 false 0.15 V 0.906,2.177 2.365,2.385 1.458,0.208 10 false Speed Sensor Rotor

for Rear
C151818E64
1.594,0.854 1.594,0.469 1.594,0.469 1.688,0.469 false 1.74,0.385 2.656,0.625 0.917,0.24 10 false Speed Sensor 4.021,2.115 4.719,2.365 0.698,0.25 10 false Low speed 6.083,1.26 6.448,1.427 0.365,0.167 10 false 0.3 V 6.083,1.625 6.563,1.792 0.479,0.167 10 false 0.15 V 4.99,2.115 5.729,2.354 0.74,0.24 10 false High speed 0.969,2.177 2.25,2.406 1.281,0.229 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area
C1330 Open in Front Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Front speed sensor RH

·

Speed sensor circuit

·

Front speed sensor installation


C1331 Open in Front Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Front speed sensor LH

·

Speed sensor circuit

·

Front speed sensor installation


C1332 Open in Rear Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Speed sensor circuit

·

Rear speed sensor installation


C1333 Open in Rear Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Skid control sensor wire LH (No. 2 parking brake wire assembly)

·

Speed sensor circuit

·

Rear speed sensor installation


C1464 Front Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not detected for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor RH

·

Speed sensor circuit

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)

·

Front speed sensor installation

·

Skid control ECU (brake actuator assembly)


C1465 Front Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not detected for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor LH

·

Speed sensor circuit

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)

·

Front speed sensor installation

·

Skid control ECU (brake actuator assembly)


C1466 Rear Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not detected for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Speed sensor circuit

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Rear speed sensor installation

·

Skid control ECU (brake actuator assembly)


C1467 Rear Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not detected for 0.4 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor LH (rear axle hub and bearing assembly LH)

·

Speed sensor circuit

·

Skid control sensor wire LH (No. 2 parking brake wire assembly)

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

·

Rear speed sensor installation

·

Skid control ECU (brake actuator assembly)



HINT:
·

DTCs C1330 and C1464 are for the front speed sensor RH.

·

DTCs C1331 and C1465 are for the front speed sensor LH.

·

DTCs C1332 and C1466 are for the rear speed sensor RH.

·

DTCs C1333 and C1467 are for the rear speed sensor LH.



DTC Detection Conditions: C1464
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition The vehicle speed is more than 50.4 km/h (31 mph). ○ - - -
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph). - ○ - -
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph). - - ○ -
Malfunction Status Pulses are not detected. ○ - - -
A wheel speed of 0 km/h (0 mph) is detected. - ○ - -
A front wheel speed of 0 km/h (0 mph) is detected. - - ○ -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - - - ○
Detection Time 0.4 seconds - - 9 to 72 seconds or more (varies depending on the driving conditions)
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1464
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition The vehicle speed is less than 100 km/h (62 mph). ○ - - -
The vehicle speed is 100 km/h (62 mph) or more. - ○ - -
Malfunction Status The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ○ - - -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - ○ - -
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. - - ○ -
An abnormal signal is received from a wheel speed sensor. - - - ○
Detection Time 9 to 72 seconds or more (varies depending on the driving conditions) 9 to 72 seconds or more (varies depending on the driving conditions) - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1465
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition The vehicle speed is more than 50.4 km/h (31 mph). ○ - - -
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph). - ○ - -
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph). - - ○ -
Malfunction Status Pulses are not detected. ○ - - -
A wheel speed of 0 km/h (0 mph) is detected. - ○ - -
A front wheel speed of 0 km/h (0 mph) is detected. - - ○ -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - - - ○
Detection Time 0.4 seconds - - 9 to 72 seconds or more (varies depending on the driving conditions)
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1465
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition The vehicle speed is less than 100 km/h (62 mph). ○ - - -
The vehicle speed is 100 km/h (62 mph) or more. - ○ - -
Malfunction Status The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ○ - - -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - ○ - -
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. - - ○ -
An abnormal signal is received from a wheel speed sensor. - - - ○
Detection Time 9 to 72 seconds or more (varies depending on the driving conditions) 9 to 72 seconds or more (varies depending on the driving conditions) - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1466
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition The vehicle speed is more than 50.4 km/h (31 mph). ○ - - -
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph). - ○ - -
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph). - - ○ -
Malfunction Status Pulses are not detected. ○ - - -
A wheel speed of 0 km/h (0 mph) is detected. - ○ - -
A rear wheel speed of 0 km/h (0 mph) is detected. - - ○ -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - - - ○
Detection Time 0.4 seconds - - 9 to 72 seconds or more (varies depending on the driving conditions)
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1466
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition The vehicle speed is less than 100 km/h (62 mph). ○ - - -
The vehicle speed is 100 km/h (62 mph) or more. - ○ - -
Malfunction Status The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ○ - - -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - ○ - -
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. - - ○ -
An abnormal signal is received from a wheel speed sensor. - - - ○
Detection Time 9 to 72 seconds or more (varies depending on the driving conditions) 9 to 72 seconds or more (varies depending on the driving conditions) - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1467
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition The vehicle speed is more than 50.4 km/h (31 mph). ○ - - -
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph). - ○ - -
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph). - - ○ -
Malfunction Status Pulses are not detected. ○ - - -
A wheel speed of 0 km/h (0 mph) is detected. - ○ - -
A rear wheel speed of 0 km/h (0 mph) is detected. - - ○ -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - - - ○
Detection Time 0.4 seconds - - 9 to 72 seconds or more (varies depending on the driving conditions)
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1467
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition The vehicle speed is less than 100 km/h (62 mph). ○ - - -
The vehicle speed is 100 km/h (62 mph) or more. - ○ - -
Malfunction Status The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5 km/h (3 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ○ - - -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of the vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - ○ - -
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. - - ○ -
An abnormal signal is received from a wheel speed sensor. - - - ○
Detection Time 9 to 72 seconds or more (varies depending on the driving conditions) 9 to 72 seconds or more (varies depending on the driving conditions) - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

for Front
C375041E03
1.427,1.542 1.854,1.792 0.427,0.25 10 false FR+ 1.24,1.427 1.667,1.677 0.427,0.25 10 false 1 2.177,1.438 2.604,1.688 0.427,0.25 10 false 2 1.146,1.844 1.573,2.094 0.427,0.25 10 false A35 1.135,2 2.792,2.25 1.656,0.25 10 false Front Speed Sensor RH 1.156,4.167 1.583,4.417 0.427,0.25 10 false A36 5.448,4.938 5.875,5.188 0.427,0.25 10 false A34 5.448,5.094 6.99,5.573 1.542,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 5.615,3.771 6.042,4.021 0.427,0.25 10 false 7 5.563,3.083 5.99,3.333 0.427,0.25 10 false 24 5.563,1.448 5.99,1.698 0.427,0.25 10 false 26 5.563,0.75 5.99,1 0.427,0.25 10 false 21 1.854,1.542 2.281,1.792 0.427,0.25 10 false FR- 5.833,0.969 6.26,1.219 0.427,0.25 10 false FR+ 5.813,1.656 6.24,1.906 0.427,0.25 10 false FR- 5.823,3.979 6.25,4.229 0.427,0.25 10 false FL- 1.875,3.865 2.302,4.115 0.427,0.25 10 false FL- 1.427,3.865 1.854,4.115 0.427,0.25 10 false FL+ 5.833,3.302 6.26,3.552 0.427,0.25 10 false FL+ 2.167,3.76 2.594,4.01 0.427,0.25 10 false 2 1.25,3.76 1.677,4.01 0.427,0.25 10 false 1 1.156,4.323 2.813,4.573 1.656,0.25 10 false Front Speed Sensor LH

for Rear
C375043E08
0.052,1.958 1.51,2.573 1.458,0.615 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 1.323,0.854 1.844,1.125 0.521,0.271 10 false u2 0.844,0.854 1.365,1.125 0.521,0.271 10 false RA+ 2.438,0.854 2.958,1.125 0.521,0.271 10 false uR1 1.625,1.958 3.188,2.635 1.563,0.677 10 false Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly) 1.323,0.625 1.844,0.896 0.521,0.271 10 false 2 1.333,1.323 1.854,1.594 0.521,0.271 10 false 1 5.563,0.75 6.083,1.021 0.521,0.271 10 false 22 5.563,1.438 6.083,1.708 0.521,0.271 10 false 37 5.552,3.135 6.073,3.406 0.521,0.271 10 false 39 5.563,3.823 6.083,4.094 0.521,0.271 10 false 23 5.438,4.99 5.958,5.26 0.521,0.271 10 false A34 5.427,5.156 6.969,5.615 1.542,0.458 10 false Skid Control ECU (Brake Actuator Assembly) 1.635,0.854 2.156,1.125 0.521,0.271 10 false RA+ 2.021,0.854 2.542,1.125 0.521,0.271 10 false RR+ 5.813,0.969 6.333,1.24 0.521,0.271 10 false RR+ 0.885,1.531 1.406,1.802 0.521,0.271 10 false RA- 0.875,3.24 1.396,3.51 0.521,0.271 10 false LA+ 1.646,1.531 2.167,1.802 0.521,0.271 10 false RA- 2.042,1.531 2.563,1.802 0.521,0.271 10 false RR- 5.802,1.635 6.323,1.906 0.521,0.271 10 false RR- 0.896,3.938 1.417,4.208 0.521,0.271 10 false LA- 1.646,3.25 2.167,3.521 0.521,0.271 10 false LA+ 2.021,3.25 2.542,3.521 0.521,0.271 10 false RL+ 5.802,3.365 6.323,3.635 0.521,0.271 10 false RL+ 1.646,3.938 2.167,4.208 0.521,0.271 10 false LA- 2.073,3.938 2.594,4.208 0.521,0.271 10 false RL- 5.802,4.042 6.323,4.313 0.521,0.271 10 false RL- 2.469,0.635 2.99,0.906 0.521,0.271 10 false 1 2.49,3.021 3.01,3.292 0.521,0.271 10 false 1 1.323,3.729 1.844,4 0.521,0.271 10 false 1 2.49,1.323 3.01,1.594 0.521,0.271 10 false 2 1.323,3.021 1.844,3.292 0.521,0.271 10 false 2 2.49,3.708 3.01,3.979 0.521,0.271 10 false 2 1.313,1.552 1.833,1.823 0.521,0.271 10 false u2 1.323,3.25 1.844,3.521 0.521,0.271 10 false v2 1.323,3.948 1.844,4.219 0.521,0.271 10 false v2 2.438,1.552 2.958,1.823 0.521,0.271 10 false uR1 2.438,3.25 2.958,3.521 0.521,0.271 10 false vR1 2.438,3.938 2.958,4.208 0.521,0.271 10 false vR1 0.063,4.354 1.5,4.885 1.438,0.531 10 false Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH) 1.625,4.354 3.188,5.083 1.563,0.729 10 false Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
C1330, C1331, C1464 or C1465 is output A
C1332, C1333, C1466 or C1467 is output B



A

2.CHECK FRONT SPEED SENSOR INSTALLATION

B

9.CHECK REAR SPEED SENSOR INSTALLATION
2.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SPEED SENSOR (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR

3.CHECK FRONT SPEED SENSOR (CHECK FOR FOREIGN MATTER)

b.

Check the front speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

4.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

4.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C248346C35
0.802,1.01 1.24,1.281 0.438,0.271 2.208,1.01 2.646,1.281 0.438,0.271 1.635,2.823 1.177,1.99 true 3.021,2.771 2.583,1.99 true 0.229,0.271 0.531,0.5 0.302,0.229 10 false *a 1.573,2.844 1.885,3.052 0.313,0.208 10 false FR+ 2.958,2.813 3.292,3.042 0.333,0.229 10 false FL+ 0.896,1.063 1.427,1.323 0.531,0.26 10 false A35 2.302,1.063 2.938,1.458 0.635,0.396 10 false A36 0.542,1.073 0.844,1.302 0.302,0.229 10 false *A 1.969,1.073 2.271,1.302 0.302,0.229 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A35 or A36 front speed sensor connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
A35-1 (FR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Condition Specified Condition
A36-1 (FL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
5.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C248346C36
0.802,1.01 1.24,1.281 0.438,0.271 2.208,1.01 2.646,1.281 0.438,0.271 1.417,2.917 1.188,1.979 true 3,2.917 2.594,1.99 true 0.5,2.917 0.885,1.979 true 2.01,2.917 2.281,1.979 true 0.229,0.271 0.531,0.5 0.302,0.229 10 false *a 1.333,2.927 1.927,3.167 0.594,0.24 10 false FR+ 2.917,2.938 3.25,3.135 0.333,0.198 10 false FL+ 0.896,1.063 1.427,1.323 0.531,0.26 10 false A35 2.313,1.063 2.948,1.458 0.635,0.396 10 false A36 0.583,1.063 0.885,1.292 0.302,0.229 10 false *A 1.979,1.063 2.281,1.292 0.302,0.229 10 false *B 0.406,2.938 1,3.177 0.594,0.24 10 false FR- 1.906,2.938 2.24,3.135 0.333,0.198 10 false FL-
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
A35-1 (FR+) - A35-2 (FR-) Ignition switch ON 11 to 14 V

for LH
Tester Connection Condition Specified Condition
A36-1 (FL+) - A36-2 (FL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR ROTOR (CHECK FOR FOREIGN MATTER)

NG

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
6.CHECK FRONT SPEED SENSOR ROTOR (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor rotor (front axle hub sub-assembly).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



HINT:
·

The front speed sensor rotor is incorporated into the front axle hub sub-assembly.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged) B
NG (There is foreign matter on the speed sensor rotor) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY

C

CLEAN FRONT SPEED SENSOR ROTOR

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A34-26 (FR-) - A35-2 (FR-) Always Below 1 Ω
A34-26 (FR-) or A35-2 (FR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A34-7 (FL-) - A36-2 (FL-) Always Below 1 Ω
A34-7 (FL-) or A36-2 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A34-21 (FR+) - A35-1 (FR+) Always Below 1 Ω
A34-21 (FR+) or A35-1 (FR+) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A34-24 (FL+) - A36-1 (FL+) Always Below 1 Ω
A34-24 (FL+) or A36-1 (FL+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK REAR SPEED SENSOR INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor
*a OK
*b NG
*c No Clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.



Result:
Proceed to
OK
NG



OK

10.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

10.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C233859C65
0.688,0.594 1.073,0.823 0.385,0.229 2.063,0.615 2.427,0.833 0.365,0.219 0.969,1.344 1.177,1.781 true 2.323,1.344 2.531,1.781 true 1.229,1.74 1.594,1.969 0.365,0.229 10 false RA+ 2.573,1.74 2.958,1.969 0.385,0.229 10 false LA+ 0.385,0.469 0.573,0.625 0.188,0.156 10 false *A 0.823,0.625 1.115,0.781 0.292,0.156 10 false u2 2.177,0.646 2.479,0.906 0.302,0.26 10 false v2 1.802,0.469 1.99,0.625 0.188,0.156 10 false *B 0.167,0.083 0.354,0.24 0.188,0.156 10 false *a
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the u2 or v2 rear speed sensor connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
u2-2 (RA+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Condition Specified Condition
v2-2 (LA+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

14.INSPECT PARKING BRAKE WIRE ASSEMBLY
11.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C233859C66
0.688,0.563 1.073,0.792 0.385,0.229 2.063,0.573 2.427,0.792 0.365,0.219 0.969,1.344 1.167,1.833 true 2.323,1.344 2.5,1.833 true 0.792,1.333 0.667,1.833 true 2.135,1.333 1.927,1.833 true 1.115,1.844 1.448,2.115 0.333,0.271 10 false RA+ 2.469,1.854 2.792,2.115 0.323,0.26 10 false LA+ 0.427,0.458 0.667,0.667 0.24,0.208 10 false *A 0.823,0.604 1.104,0.813 0.281,0.208 10 false u2 2.177,0.604 2.552,0.885 0.375,0.281 10 false v2 1.802,0.458 2.052,0.729 0.25,0.271 10 false *B 0.135,0.156 0.323,0.313 0.188,0.156 10 false *a 1.844,1.844 2.219,2.031 0.375,0.188 10 false LA- 0.573,1.833 0.948,2.021 0.375,0.188 10 false RA-
*A for RH
*B for LH
*a Front view of wire harness connector
(to Rear Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
u2-2 (RA+) - u2-1 (RA-) Ignition switch ON 11 to 14 V

for LH
Tester Connection Condition Specified Condition
v2-2 (LA+) - v2-1 (LA-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

NG

12.INSPECT PARKING BRAKE WIRE ASSEMBLY
12.INSPECT PARKING BRAKE WIRE ASSEMBLY
a.
C367773C43
0.833,0.417 1.333,0.667 0.5,0.25 0.833,0.75 1.333,1 0.5,0.25 2.25,0.417 2.75,0.667 0.5,0.25 2.25,0.75 2.75,1 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 1.365,0.448 1.729,0.698 0.365,0.25 10 false *A 1.365,0.781 1.729,1.063 0.365,0.281 10 false *B 0.25,0.208 0.563,0.365 0.313,0.156 10 false *a 0.99,1.052 1.302,1.208 0.313,0.156 10 false *b 2.406,1.083 2.719,1.24 0.313,0.156 10 false *c 2.781,0.458 3.167,0.698 0.385,0.24 10 false *A 2.771,0.781 3.125,0.99 0.354,0.208 10 false *B 0.375,2.542 0.969,2.719 0.594,0.177 10 false RA-*A 1.281,2.552 1.875,2.729 0.594,0.177 10 false RA+*A 1.896,2.396 2.479,2.615 0.583,0.219 10 false RR+*A 2.708,2.375 3.302,2.625 0.594,0.25 10 false RR-*A 0.375,2.729 0.906,2.917 0.531,0.188 10 false LA-*B 1.292,2.719 1.823,2.938 0.531,0.219 10 false LA+*B 2.729,2.552 3.24,2.75 0.51,0.198 10 false RL-*B 1.906,2.573 2.385,2.75 0.479,0.177 10 false RL+*B 1.01,0.458 1.323,0.615 0.313,0.156 10 false u2 1.01,0.792 1.396,1.063 0.385,0.271 10 false v2 2.396,0.458 2.813,0.656 0.417,0.198 10 false uR1 2.396,0.792 2.75,1.031 0.354,0.24 10 false vR1
*A for RH
*B for LH
*a Front view of skid control sensor wire (parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly) or the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
u2-1 (RA-) - uR1-2 (RR-) Always Below 1 Ω
u2-1 (RA-) - uR1-1 (RR+) Always 10 kΩ or higher
u2-1 (RA-) or uR1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
v2-1 (LA-) - vR1-2 (RL-) Always Below 1 Ω
v2-1 (LA-) - vR1-1 (RL+) Always 10 kΩ or higher
v2-1 (LA-) or vR1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - PARKING BRAKE WIRE ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A34-37 (RR-) - uR1-2 (RR-) Always Below 1 Ω
A34-37 (RR-) or uR1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A34-23 (RL-) - vR1-2 (RL-) Always Below 1 Ω
A34-23 (RL-) or vR1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT PARKING BRAKE WIRE ASSEMBLY
a.
C367773C43
0.833,0.417 1.333,0.667 0.5,0.25 0.833,0.75 1.333,1 0.5,0.25 2.25,0.417 2.75,0.667 0.5,0.25 2.25,0.75 2.75,1 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 1.365,0.448 1.729,0.698 0.365,0.25 10 false *A 1.365,0.781 1.729,1.063 0.365,0.281 10 false *B 0.25,0.208 0.563,0.365 0.313,0.156 10 false *a 0.99,1.052 1.302,1.208 0.313,0.156 10 false *b 2.406,1.083 2.719,1.24 0.313,0.156 10 false *c 2.781,0.458 3.167,0.698 0.385,0.24 10 false *A 2.771,0.781 3.125,0.99 0.354,0.208 10 false *B 0.375,2.542 0.969,2.719 0.594,0.177 10 false RA-*A 1.281,2.552 1.875,2.729 0.594,0.177 10 false RA+*A 1.896,2.396 2.479,2.615 0.583,0.219 10 false RR+*A 2.708,2.375 3.302,2.625 0.594,0.25 10 false RR-*A 0.375,2.729 0.906,2.917 0.531,0.188 10 false LA-*B 1.292,2.719 1.823,2.938 0.531,0.219 10 false LA+*B 2.729,2.552 3.24,2.75 0.51,0.198 10 false RL-*B 1.906,2.573 2.385,2.75 0.479,0.177 10 false RL+*B 1.01,0.458 1.323,0.615 0.313,0.156 10 false u2 1.01,0.792 1.396,1.063 0.385,0.271 10 false v2 2.396,0.458 2.813,0.656 0.417,0.198 10 false uR1 2.396,0.792 2.75,1.031 0.354,0.24 10 false vR1
*A for RH
*B for LH
*a Front view of skid control sensor wire (parking brake wire assembly)
*b Front view of wire harness connector
(to Sensor Side Connector)
*c Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly) or the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
u2-2 (RA+) - uR1-1 (RR+) Always Below 1 Ω
u2-2 (RA+) - uR1-2 (RR-) Always 10 kΩ or higher
u2-2 (RA+) or uR1-1 (RR+) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
v2-2 (LA+) - vR1-1 (RL+) Always Below 1 Ω
v2-2 (LA+) - vR1-2 (RL-) Always 10 kΩ or higher
v2-2 (LA+) or vR1-1 (RL+) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - PARKING BRAKE WIRE ASSEMBLY)

NG

REPLACE PARKING BRAKE WIRE ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - PARKING BRAKE WIRE ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A34-22 (RR+) - uR1-1 (RR+) Always Below 1 Ω
A34-22 (RR+) or uR1-1 (RR+) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A34-39 (RL+) - vR1-1 (RL+) Always Below 1 Ω
A34-39 (RL+) or vR1-1 (RL+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR