Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1426  Stop Light Switch OFF Stuck Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch assembly signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect a short in the stop light input signal circuit or stop light circuit when the stop light switch assembly is on (brake pedal depressed).

If the skid control ECU (brake actuator assembly) detects a short in this circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1426 Stop Light Switch OFF Stuck Malfunction Either of the following is detected when the vehicle speed of 3 km/h (2 mph) or more:
1.

With the stop light switch assembly off, the stop light switch assembly is judged to be on based on the master cylinder pressure value for 3 seconds or more.

2.

With the stop light switch assembly off, the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1160 psi) for 3 seconds or more.


·

Wire harness or connector

·

Stop light switch assembly

·

Skid Control ECU (brake Actuator Assembly)



DTC Detection Conditions: C1426
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition The vehicle speed of 3 km/h (2 mph) or more. ○ ○
The stop light switch assembly is off. ○ ○
Malfunction Status The stop light switch assembly is judged to be on based on the master cylinder pressure value. ○ -
The master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1160 psi). - ○
Detection Time 3 seconds or more 3 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (BS1 VOLTAGE VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BS1 Voltage Value +BS voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
Chassis > ABS/VSC/TRC > Data List
Tester Display
BS1 Voltage Value
50003 105 273

d.

Take a note of the +BS voltage value.

HINT:

The noted +BS voltage value is used in a later step.



Result:
Proceed to
NEXT



NEXT

2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the brake pedal height installation.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT


b.

Check the stop light switch assembly installation.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION


OK:

The brake pedal height and stop light switch assembly installation are normal.


HINT:

If the on/off status of the stop light switch assembly and pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and switch before inspecting the input signals and other related parts.


Result:
Proceed to
OK
NG



OK

3.CHECK STOP LIGHT OPERATION

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

3.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

4.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
4.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

5.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays on or off according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

6.RECONFIRM DTC

NG

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
6.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 3 km/h (2 mph) or more and depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
C1426 is not output A
C1426 is output B



A

B

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C360727C71
0.271,0.281 0.719,0.531 0.448,0.25 2.563,0.365 2.208,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.365,0.323 0.708,0.542 0.344,0.219 10 false A34 2.479,0.188 2.906,0.375 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C360727C70
0.302,0.302 0.74,0.552 0.438,0.25 2.396,0.344 2.74,0.99 true 0.135,0.063 0.448,0.26 0.313,0.198 10 false *a 0.385,0.333 0.698,0.531 0.313,0.198 10 false A34 2.219,0.177 2.719,0.385 0.5,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-46 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C360727C71
0.271,0.281 0.719,0.531 0.448,0.25 2.563,0.365 2.208,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.365,0.323 0.708,0.542 0.344,0.219 10 false A34 2.479,0.188 2.906,0.375 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

11.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

11.RECONFIRM DTC
a.

Reconnect the A34 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 3 km/h (2 mph) or more and depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
C1426 is not output A
C1426 is output B


HINT:

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly).

for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL

for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL




A

B