The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the brake system warning light (red indicator) remains on:
The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
The brake fluid level is insufficient.
The vacuum inside the brake booster decreases (except 2AR-FE).
EBD operation is not possible.
When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the battery voltage.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) terminal - Negative (-) terminal | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2AR-FE: Click herePower Source / Network>2AR-FE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for A25A-FKS: Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
for 2GR-FKS: Click herePower Source / Network>2GR-FKS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A34 skid control ECU (brake actuator assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-30 (+BS) - Body ground | Always | 11 to 14 V |
| A34-36 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-46 (GND1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly)) |
Turn the ignition switch off.
Reconnect the A34 skid control ECU (brake actuator assembly) connector.
Remove the reservoir filler cap and strainer.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
A float is located inside the reservoir. Its position changes according to the brake fluid level.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+) - 2 (E) | Switch off (float up) | 1.9 to 2.1 kΩ |
| 1 (+) - 2 (E) | Switch on (float down) | Below 1 Ω |
If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER (for LHD)>DISASSEMBLY
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER (for RHD)>DISASSEMBLY
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the K21 combination meter assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-12 (SW) - A1-1 (+) | Always | Below 1 Ω |
| K21-12 (SW) or A1-1 (+) - Body ground | Always | 10 kΩ or higher |
| A1-2 (E) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (except 2AR-FE) | A |
| OK (for 2AR-FE) | B |
| NG | C |
A
B
C
Reconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
Reconnect the K21 combination meter assembly connector.
Inspect the vacuum warning switch assembly.
Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH>ON-VEHICLE INSPECTION
The vacuum warning switch assembly is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Disconnect the A2 vacuum warning switch assembly connector.
Disconnect the K21 combination meter assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K21-7 (VCM) - A2-2 (+) | Always | Below 1 Ω |
| K21-7 (VCM) or A2-2 (+) - Body ground | Always | 10 kΩ or higher |
| A2-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A2 vacuum warning switch assembly connector.
Reconnect the K21 combination meter assembly connector.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Brake Warning Light | Brake system warning light (red indicator) | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Tester Display |
|---|
| Brake Warning Light |
Check the GTS display condition of the brake system warning light (red indicator).
| Result | Proceed to |
|---|---|
| The value of Brake Warning Light is ON | A |
| The value of Brake Warning Light is OFF | B |
A
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Reconnect the K21 combination meter assembly connector.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Brake Warning Light | Brake system warning light (red indicator) | ON or OFF | ON: Warning light on
OFF: Warning light off |
- |
| Tester Display |
|---|
| Brake Warning Light |
Check the GTS display condition of the brake system warning light (red indicator).
| Result | Proceed to |
|---|---|
| The value of Brake Warning Light is ON | A |
| The value of Brake Warning Light is OFF | B |
A
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING