Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1234  Yaw Rate Sensor  C1472  Acceleration Sensor  C1474  Forward and Rearward G Sensor  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0123 (Lost Communication with Yaw Rate Sensor Module) is output. When U0123 is output together with C1234, C1472 and/or C1474, inspect and repair the trouble areas indicated by U0123 first.


These DTCs may be stored if one of the following occurs:

·

Yaw rate and acceleration sensor circuit malfunction.

·

Yaw rate and acceleration sensor (airbag sensor assembly) installation abnormality.

·

Yaw rate and acceleration sensor signal malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1234 Yaw Rate Sensor Any of the following is detected:
1.

The yaw rate sensor offset value is estimated as less than -5.25 deg/s or more than 5.25 deg/s based on offset correction performed when the vehicle is stopped and then the vehicle starts off.

2.

The offset correction did not complete with the vehicle stopped, and the yaw rate sensor offset value is estimated as less than -15 deg/s or more than 15 deg/s based on the offset correction performed while the vehicle is being driven.

3.

The offset correction completed with the vehicle stopped and the yaw rate sensor offset value is less than -7.5 deg/s or more than 7.5 deg/s.

4.

The yaw rate sensor offset value is estimated as less than -7.5 deg/s or more than 7.5 deg/s based on the offset correction performed while the vehicle is being driven.

5.

After the VSC system has turned on, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 5 seconds or more when the vehicle is stopped.

6.

After the VSC system has turned on, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more when the vehicle starts off.

7.

After the VSC system has turned on, but before the vehicle starts off, as the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more.

8.

The yaw rate sensor value is less than -94.75 deg/s or more than 94.75 deg/s for 0.8 seconds or more.

9.

The change of the yaw rate sensor value within 0.04 seconds is abnormal.

10.

The value from the yaw rate sensor is judged as abnormal based on the skid control ECU (brake actuator assembly) estimation.


·

Yaw rate sensor (airbag sensor assembly) installation

·

Yaw rate sensor (airbag sensor assembly)

·

Yaw rate sensor circuit


C1472 Acceleration Sensor Any of the following is detected:
1.

With the vehicle stopped, the internal acceleration value is less than -7 m/s2 or more than 7 m/s2 for 0.4 seconds or more.

2.

The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed while the vehicle is being driven.

3.

The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2 for 0.8 seconds or more.


·

Acceleration sensor (airbag sensor assembly) installation

·

Acceleration sensor (airbag sensor assembly)

·

Acceleration sensor circuit


C1474 Forward and Rearward G Sensor Any of the following is detected:
1.

The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed while the vehicle is being driven.

2.

The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2 for 3 seconds or more.


·

Acceleration sensor (airbag sensor assembly) installation

·

Acceleration sensor (airbag sensor assembly)

·

Acceleration sensor circuit



DTC Detection Conditions: C1234
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnosis Condition The offset correction did not complete with the vehicle stopped. - ○ - - -
The offset correction completed with the vehicle stopped. - - ○ - -
The vehicle is being driven. - - - ○ -
The VSC system has turned on, but the vehicle has not started off. - - - - ○
Malfunction Status The yaw rate sensor offset value is estimated as less than -5.25 deg/s or more than 5.25 deg/s based on offset correction performed when the vehicle is stopped and then the vehicle starts off. ○ - - - -
The yaw rate sensor offset value is estimated as less than -15 deg/s or more than 15 deg/s based on the offset correction performed while the vehicle is being driven. - ○ - - -
The yaw rate sensor offset value is less than -7.5 deg/s or more than 7.5 deg/s. - - ○ - -
The yaw rate sensor offset value is estimated as less than -7.5 deg/s or more than 7.5 deg/s based on the offset correction performed. - - - ○ -
The yaw rate sensor value is less than -30 deg/s or more than 30 deg/s. - - - - ○
Detection Time - - - - 5 seconds or more when the vehicle is stopped.
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1234
Vehicle Condition
Pattern 6 Pattern 7 Pattern 8 Pattern 9 Pattern 10
Diagnosis Condition The VSC system has turned on, but the vehicle has not started off. ○ ○ - - -
Malfunction Status The yaw rate sensor value is less than -30 deg/s or more than 30 deg/s. ○ - - - -
As the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s. - ○ - - -
The yaw rate sensor value is less than -94.75 deg/s or more than 94.75 deg/s. - - ○ - -
The change of the yaw rate sensor value within 0.04 seconds is abnormal. - - - ○ -
The value from the yaw rate sensor is judged as abnormal based on the skid control ECU (brake actuator assembly) estimation. - - - - ○
Detection Time 0.5 seconds or more when the vehicle starts off. 0.5 seconds or more 0.8 seconds or more - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1472
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition The vehicle stopped. ○ - -
Vehicle is being driven. - ○ -
Malfunction Status The internal acceleration value is less than -7 m/s2 or more than 7 m/s2. ○ - -
The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed. - ○ -
The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2. - - ○
Detection Time 0.4 seconds or more - 0.8 seconds or more
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1474
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition The vehicle is being driven. ○ -
Malfunction Status The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed. ○ -
The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2. - ○
Detection Time - 3 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C275041E44
0.802,0.708 1.417,0.906 0.615,0.198 10 false CANL 6.052,0.719 6.667,0.917 0.615,0.198 10 false CANL 0.792,1.323 1.406,1.521 0.615,0.198 10 false CANH 6.042,1.323 6.656,1.521 0.615,0.198 10 false CANH 0.938,1.938 1.229,2.177 0.292,0.24 10 false IG2 0.979,2.552 1.292,2.75 0.313,0.198 10 false E1 0.958,3.167 1.271,3.365 0.313,0.198 10 false E2 1.292,0.552 1.604,0.75 0.313,0.198 10 false 27 1.292,1.156 1.604,1.354 0.313,0.198 10 false 26 1.302,1.844 1.615,2.042 0.313,0.198 10 false 36 1.292,2.448 1.604,2.646 0.313,0.198 10 false 33 1.302,3.052 1.615,3.25 0.313,0.198 10 false 32 5.76,0.542 6.073,0.74 0.313,0.198 10 false 19 5.813,1.146 6.083,1.365 0.271,0.219 10 false 5 2.135,2.094 2.906,2.281 0.771,0.188 10 false A/BAG-IG2 3.927,1.938 5.385,2.156 1.458,0.219 10 false from IG2-NO. 2 Relay 0.063,3.896 0.521,4.094 0.458,0.198 10 false K73 0.052,4.063 2.208,4.531 2.156,0.469 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 5.573,3.938 7.125,4.344 1.552,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 5.583,3.76 6.042,3.958 0.458,0.198 10 false A34 3.677,3.406 5.479,3.635 1.802,0.229 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION



HINT:

When U0123 and/or U0126 is output together with C1234, C1472 and/or C1474, inspect and repair the trouble areas indicated by U0123 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

At a speed of 30 km/h (18 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C374261C01
0.219,0.583 0.583,0.865 0.365,0.281 2.771,2.823 2.24,2.333 true 0.177,0.229 0.49,0.385 0.313,0.156 10 false *a 0.281,0.635 0.74,0.833 0.458,0.198 10 false K73 2.802,2.771 3.26,2.969 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the K73 yaw rate and acceleration sensor (airbag sensor assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K73-36 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C374261C02
0.219,0.583 0.583,0.865 0.365,0.281 2.344,3.042 1.854,2.333 true 1.24,3.042 1.698,2.333 true 0.177,0.229 0.49,0.385 0.313,0.156 10 false *a 0.281,0.635 0.74,0.833 0.458,0.198 10 false K73 2.292,3.052 2.75,3.25 0.458,0.198 10 false E1 1.167,3.052 1.479,3.25 0.313,0.198 10 false E2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K73-33 (E1) - Body ground Always Below 1 Ω
K73-32 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)