Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1336  Zero Point Calibration of Acceleration Sensor Undone  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If a communication error with the yaw rate and acceleration sensor (airbag sensor assembly) is detected, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0151 (Lost Communication with Airbag ECU) are stored.

The DTCs are also stored when the calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1336 Zero Point Calibration of Acceleration Sensor Undone Zero point calibration of acceleration sensor undone.
·

Acceleration sensor (airbag sensor assembly) installation

·

Acceleration sensor (airbag sensor assembly)

·

Skid control ECU (brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION



HINT:

When U0123 and/or U0151 is output together with C1336, inspect and repair the trouble areas indicated by U0123 and/or U0151 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.


b.

Perform zero point calibration of the yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

Chassis > ABS/VSC/TRC > Utility
Tester Display
Test Mode
50005 105 166

Result:
Proceed to
NEXT



NEXT

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.


c.

Using the GTS, perform a Test Mode (Signal Check) inspection sensor check and check that all Test Mode (Signal Check) inspection items change from incomplete to complete.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 4359
OK:

All Test Mode (Signal Check) inspection items change from incomplete to complete



Result:
Proceed to
OK
NG



OK

END

NG

3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (ACCELERATION SENSOR)

NG

4.READ VALUE USING GTS (ACCELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Deceleration Sensor Acceleration sensor reading Min.: -18.525 m/s2
Max.: 18.387 m/s2
- During deceleration/acceleration: Changes continuously
Deceleration Sensor2 Acceleration sensor 2 reading Min.: -18.525 m/s2
Max.: 18.387 m/s2
- During deceleration/acceleration: Changes continuously
Chassis > ABS/VSC/TRC > Data List
Tester Display
Deceleration Sensor
Deceleration Sensor2
50003 105 14,15

d.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.



Result:
Proceed to
OK
NG



OK

NG