Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)
RM33A0E _58 Vehicle Interior _065386 SEAT BELT _0327385 SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/ Occupant Classification System)  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The seat belt warning light on the combination meter assembly illuminates, blinks or turns off in accordance with the state of the front seat inner belt assembly LH.

WIRING DIAGRAM

B424815E20
0.5,2.406 2.198,2.604 1.698,0.198 10 false : CAN Communication Line 0.042,1.885 1.885,2.25 1.844,0.365 10 false Combination Meter Assembly 2.677,1.875 4.396,2.094 1.719,0.219 10 false Airbag Sensor Assembly 2.698,1.708 3.813,1.958 1.115,0.25 10 false R32 3.781,0.563 4.844,0.875 1.063,0.313 10 false LBE- 5.677,0.469 6.865,0.708 1.188,0.24 10 false LBE- 5.677,1.51 6.844,1.781 1.167,0.271 10 false LBE+ 4.208,1.26 4.917,1.51 0.708,0.25 10 false 28 3.792,1.365 4.958,1.635 1.167,0.271 10 false LBE+ 5.479,0.469 5.927,0.677 0.448,0.208 10 false 1 4.219,0.479 5.052,0.74 0.833,0.26 10 false 27 5.479,1.271 5.927,1.479 0.448,0.208 10 false 2 5.604,1.885 6.667,2.104 1.063,0.219 10 false R69 5.604,2.052 6.917,2.417 1.313,0.365 10 false Front Seat Inner Belt Assembly LH

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system (w/ occupant classification system) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)>HOW TO PROCEED WITH TROUBLESHOOTING


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)>ON-VEHICLE INSPECTION

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


PROCEDURE

1.CHECK DTC OUTPUT (AIRBAG SYSTEM)
a.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 188

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 188

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (LEFT SIDE BUCKLE SW)

B

2.READ VALUE USING GTS (LEFT SIDE BUCKLE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / SRS Airbag / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > SRS Airbag > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Left side Buckle SW LH buckle switch Unset, Set or NG Unset: Seat belt not fastened
Set: Seat belt fastened
NG: Data is not determined
-
Body Electrical > SRS Airbag > Data List
Tester Display
Left side Buckle SW
50003 188 4

Result:
Result Proceed to
Unset or Set is displayed on the GTS according to the driver seat belt condition A
Unset or Set is not displayed correctly on the GTS according to the driver seat belt condition B
NG is displayed on the GTS C



A

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

C