Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/o Occupant Classification System) › 2017.09–2021.02
RM33A0E _58 Vehicle Interior _065386 SEAT BELT _0327396 SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (driver seat).

WIRING DIAGRAM

B287218E56
4.167,0.823 4.438,1.063 0.271,0.24 10 false 3D 4.188,0.625 4.385,0.792 0.198,0.167 10 false 33 2.677,0.844 3.073,1.229 0.396,0.385 10 false DBKL 0.094,1.531 1.292,2.031 1.198,0.5 10 false Combination Meter Assembly 0.573,2.448 2.292,2.656 1.719,0.208 10 false : CAN Communication Line 3.125,0.708 3.323,0.938 0.198,0.229 10 false 18 5.26,0.719 5.458,0.99 0.198,0.271 10 false 3 6.094,0.719 6.333,1.063 0.24,0.344 10 false 2 1.708,1.688 3.354,2.063 1.646,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 4.844,1.094 5.917,1.438 1.073,0.344 10 false R70*1, R71*2 4.833,1.271 6.771,1.75 1.938,0.479 10 false Front Seat Inner Belt Assembly (Driver Seat) 3.5,1.25 4.583,1.792 1.083,0.542 10 false Instrument Panel Junction Block Assembly 3.969,2.448 7.156,2.792 3.188,0.344 10 false *2: for RHD 3.969,2.125 7.156,2.469 3.188,0.344 10 false *1: for LHD 1.708,1.531 1.979,1.771 0.271,0.24 10 false MB 5.427,0.729 5.583,0.927 0.156,0.198 10 false + 5.875,0.74 6.031,0.938 0.156,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system (w/o occupant classification system) uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat*. Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)>ON-VEHICLE INSPECTION

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL

*: w/ Front Passenger Seat Belt Warning System



PROCEDURE

1.READ VALUE USING GTS (D SEAT BUCKLE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch ON or OFF ON: Driver seat belt fastened
OFF: Driver seat belt unfastened
-
Body Electrical > Main Body > Data List
Tester Display
D Seat Buckle SW
50003 123 14
OK:

ON or OFF appears on the GTS screen according to the driver seat belt condition.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)
2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)
a.

Remove the front seat inner belt assembly (driver seat).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the front seat inner belt assembly (driver seat).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B491251C01
1.948,0.719 2.365,0.958 0.417,0.24 5.552,0.625 5.948,0.865 0.396,0.24 2.417,2 2.417,1.573 false 5.667,0.656 5.979,0.854 0.313,0.198 10 false 3D 2.052,0.76 2.365,0.958 0.313,0.198 10 false MB 0.344,0.167 0.656,0.365 0.313,0.198 10 false *a 2.25,2 2.865,2.198 0.615,0.198 10 false DBKL
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-18 (DBKL) - 3D-33 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT) - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
3D-33 - R70-3(+) Always Below 1 Ω
R70-3(+) or 3D-33 - Body ground Always 10 kΩ or higher
R70-2(E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
3D-33 - R71-3(+) Always Below 1 Ω
R71-3(+) or 3D-33 - Body ground Always 10 kΩ or higher
R71-2(E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR