Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2017.09–2018.04
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0327417 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Cooling is Poor  


DESCRIPTION

If the cooling effect of the air conditioning system is weak, the following factors may be the cause.

Symptom Factor
·

Cooling effectiveness is poor

·

Cooling response is slow


·

ECO mode control of air conditioning system is enabled*1

·

Compressor assembly with pulley (compressor solenoid) malfunction*2

·

Cooler compressor assembly (compressor solenoid) malfunction*3

·

Refrigerant volume (high)

·

Refrigerant volume (low)

·

Clogged cooler condenser assembly fins

·

Cooling fan system malfunction

·

Mechanical locking of damper and damper link

·

Automatic light control sensor malfunction

·

High inlet air temperature

·

Harness or connector



*1: w/ ECO Switch

*2: except 2GR-FKS

*3: for 2GR-FKS


WIRING DIAGRAM

E370999E04
0.042,1.01 2.365,1.219 2.323,0.208 10 false Air Conditioning Amplifier Assembly 3.156,1.646 3.625,1.833 0.469,0.188 10 false CLTB 3.146,2.438 3.615,2.625 0.469,0.188 10 false CLTS 3.156,3.094 3.625,3.281 0.469,0.188 10 false CLTE 3.594,1.646 3.771,1.844 0.177,0.198 10 false 1 3.615,2.438 3.792,2.635 0.177,0.198 10 false 4 3.625,3.094 3.802,3.292 0.177,0.198 10 false 2 4.594,1.646 4.771,1.844 0.177,0.198 10 false 23 4.854,1.646 5.271,1.813 0.417,0.167 10 false CLTB 4.604,2.438 4.781,2.635 0.177,0.198 10 false 24 4.875,2.438 5.292,2.604 0.417,0.167 10 false CLTS 4.604,3.094 4.781,3.292 0.177,0.198 10 false 25 4.854,3.104 5.271,3.271 0.417,0.167 10 false CLTE 1.833,3.896 2.135,4.083 0.302,0.188 10 false M1 1.833,4.052 3.927,4.25 2.094,0.198 10 false Automatic Light Control Sensor 4.906,4.198 6.583,4.563 1.677,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 4.917,4.021 5.219,4.208 0.302,0.188 10 false K52 1.052,4.469 3.146,4.667 2.094,0.198 10 false : CAN Communication Line 5.938,2.552 6.25,2.75 0.313,0.198 10 false IC 2.292,2.552 2.604,2.75 0.313,0.198 10 false IC

PROCEDURE

1.CONFIRM MODEL
Result:
Result Proceed to
w/ ECO Switch A
w/o ECO Switch B



A

2.CHECK ECO MODE CONTROL OPERATION

B

3.PERFORM REFRIGERANT SHORTAGE CHECK
2.CHECK ECO MODE CONTROL OPERATION
a.

Check that ECO mode control is disabled (ECO mode indicator is not illuminated).


b.

Operate the ECO switch assembly (electric parking brake switch assembly) and check that the ECO mode indicator illuminates and the blower speed is reduced.

HINT:
·

When ECO mode control is operating, the air conditioning amplifier assembly controls the air conditioning system to enhance fuel efficiency. Therefore, explain to the customer that, when ECO mode control is operating, the blower speed will be reduced.

Control Outline
Blower Control When the air conditioning system is in AUTO mode, the blower speed will be reduced to a certain speed. Additionally, if warm-up control is operating, the blower speed will be further reduced.
Air Inlet Control If the ambient temperature is a certain value or more, the air inlet mode will be changed to recirculation mode.

·

In some situations, ECO mode control may not operate even though it is enabled.




c.

Operate the ECO switch assembly (electric parking brake switch assembly) and check that the ECO mode indicator turns off and the blower speed returns to normal.

OK:

When the ECO switch assembly (electric parking brake switch assembly) is operated, ECO mode control is enabled/disabled and the blower speed is controlled.



Result:
Proceed to
OK
NG



OK

3.PERFORM REFRIGERANT SHORTAGE CHECK

NG

3.PERFORM REFRIGERANT SHORTAGE CHECK
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Utility / Refrigerant Gas Volume Check.

Body Electrical > Air Conditioner > Utility
Tester Display
Refrigerant Gas Volume Check
50005 121 3186

e.

Check that the following conditions are met and perform the refrigerant shortage check according to the display on the GTS.

Measurement Condition:
Item Condition
A/C switch On
Ambient temperature* 0 to 49°C (32 to 120°F)
Blower speed HI

*: If the ambient temperature is not within the range shown, do not perform this check.


Result:
Result Amount of Refrigerant
Refrigerant correct Correct
Refrigerant shortage Insufficient


OK:

"Refrigerant correct" is displayed on the GTS.


Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS

NG

4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (driver side air mix) pulse Min.: 128
Max.: 383
for LHD

Operates between 165 to 257 pulses


for RHD

Operates between 255 to 347 pulses


Air Mix Servo Targ Pulse(P) No. 1 air conditioning radiator damper servo sub-assembly (front passenger side air mix) pulse Min.: 128
Max.: 383
for LHD:

Operates between 255 to 347 pulses


for RHD:

Operates between 165 to 257 pulses


Rear Air Mix Servo Targ Pulse No. 3 air conditioning radiator damper servo sub-assembly pulse Min.: 128
Max.: 383
·

Operates between 165 to 257 pulses

·

*


*: for 3 Zone Type


Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(D)
50004 121 24
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Mix Servo Targ Pulse(P)
50004 121 25
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Air Mix Servo Targ Pulse
50004 121 36
OK:

Each damper servo motor operates.



Result:
Proceed to
OK
NG



OK

5.INSPECT HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

5.INSPECT HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the M1 automatic light control sensor connector.


b.

Disconnect the K52 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified
Condition
M1-1 (CLTB) - K52-23 (CLTB) Always Below 1 Ω
M1-2 (CLTE) - K52-25 (CLTE) Always Below 1 Ω
M1-4 (CLTS) - K52-24 (CLTS) Always Below 1 Ω
M1-1 (CLTB) or K52-23 (CLTB) - Other terminals and body ground Always 10 kΩ or higher
M1-2 (CLTE) or K52-25 (CLTE) - Other terminals and body ground Always 10 kΩ or higher
M1-4 (CLTS) or K52-24 (CLTS) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.

Remove the automatic light control sensor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL


b.

Inspect the automatic light control sensor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

INSPECT REFRIGERANT PRESSURE WITH MANIFOLD GAUGE SET

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR