Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM33A0E _57 Power Source / Network _065377 NETWORKING _0321446 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in Bus 4 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 22 (CA2H) and 7 (CA2L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

Airbag sensor assembly

·

No. 2 CAN junction connector

·

No. 4 CAN junction connector

·

No. 3 junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C382084E01
0.063,1.406 0.521,1.604 0.458,0.198 10 false K76 0.375,1.406 2.344,1.896 1.969,0.49 10 false Central Gateway ECU (Network Gateway ECU) 0.427,0.698 0.885,0.896 0.458,0.198 10 false 120 Ω 0.979,0.875 1.438,1.073 0.458,0.198 10 false CA2L 0.948,0.344 1.406,0.542 0.458,0.198 10 false CA2H 1.458,0.313 1.917,0.51 0.458,0.198 10 false 22 1.479,0.844 1.938,1.042 0.458,0.198 10 false 7 2.844,0.854 3.302,1.052 0.458,0.198 10 false 21 2.823,0.313 3.281,0.51 0.458,0.198 10 false 10 3.99,0.313 4.448,0.51 0.458,0.198 10 false 11 4.01,0.844 4.469,1.042 0.458,0.198 10 false 22 2.708,1.396 3.167,1.594 0.458,0.198 10 false R99 3.042,1.396 4.719,1.938 1.677,0.542 10 false No. 3 Junction Connector 4.01,2.365 4.469,2.563 0.458,0.198 10 false 2 3.979,2.896 4.438,3.094 0.458,0.198 10 false 13 2.813,2.896 3.271,3.094 0.458,0.198 10 false 16 2.885,2.365 3.344,2.563 0.458,0.198 10 false 5 2.698,3.448 3.156,3.646 0.458,0.198 10 false A67 3.052,3.448 5.094,3.896 2.042,0.448 10 false No. 2 CAN Junction Connector 2.688,4.708 3.146,4.906 0.458,0.198 10 false K127 2.802,4.479 3.26,4.677 0.458,0.198 10 false 6 2.76,5 3.219,5.198 0.458,0.198 10 false 17 2.698,5.24 3.156,5.438 0.458,0.198 10 false K127 3.969,5.24 4.427,5.438 0.458,0.198 10 false K128 4.042,5 4.5,5.198 0.458,0.198 10 false 17 3.958,4.708 4.417,4.906 0.458,0.198 10 false K128 3.052,5.656 5.219,6.021 2.167,0.365 10 false No. 4 CAN Junction Connector 4.073,4.469 4.531,4.667 0.458,0.198 10 false 6 5.563,4.583 6.021,4.781 0.458,0.198 10 false 26 5.563,5.115 6.021,5.313 0.458,0.198 10 false 27 5.844,5.135 6.302,5.333 0.458,0.198 10 false CANL 5.844,4.594 6.302,4.792 0.458,0.198 10 false CANH 5.479,5.677 5.938,5.875 0.458,0.198 10 false K73 5.823,5.677 6.76,6.167 0.938,0.49 10 false Airbag Sensor Assembly 6.385,4.969 6.844,5.167 0.458,0.198 10 false 120 Ω

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 3 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the R99 No. 3 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C372332C16
1.323,1.344 1.813,1.615 0.49,0.271 4.427,1.427 4.427,0.594 4.427,0.594 4.594,0.594 true 4.26,1.708 4.26,2.208 4.26,2.208 4.094,2.208 true 4.427,1.698 4.427,2.198 4.427,2.198 4.594,2.198 true 4.271,1.438 4.271,0.604 4.271,0.604 4.104,0.604 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.448,1.406 1.865,1.667 0.417,0.26 10 false R99 3.542,0.531 4.219,0.823 0.677,0.292 10 false CANH*b 3.552,2.125 4.229,2.417 0.677,0.292 10 false CANL*b 4.667,0.521 5.344,0.813 0.677,0.292 10 false CANH*c 4.667,2.115 5.344,2.406 0.677,0.292 10 false CANL*c
*a Front view of wire harness connector
(to No. 3 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to No. 2 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
R99-10 (CANH) - R99-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
R99-11 (CANH) - R99-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to No. 2 CAN junction connector) C



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 3 JUNCTION CONNECTOR)

C

3.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the R99 No. 3 junction connector.


b.

Disconnect the K76 central gateway ECU (network gateway ECU) connector.


c.
C364670C17
1.479,0.156 1.906,0.385 0.427,0.229 2.417,0.906 2.417,0.292 2.417,0.292 2.573,0.292 true 2.49,1.823 2.323,1.823 2.323,1.823 2.323,1.219 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.583,0.188 2.042,0.385 0.458,0.198 10 false K76 2.656,0.219 3.094,0.417 0.438,0.198 10 false CA2L 2.573,1.74 3.125,1.938 0.552,0.198 10 false CA2H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K76-22 (CA2H) - K76-7 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 3 JUNCTION CONNECTOR)

3.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the R99 No. 3 junction connector.


b.

Disconnect the A67 No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C372332C17
1.323,1.344 1.813,1.615 0.49,0.271 3.417,1.427 3.417,0.594 3.417,0.594 3.583,0.594 true 2.917,1.698 2.917,2.198 2.917,2.198 2.75,2.198 true 3.427,1.698 3.427,2.198 3.427,2.198 3.594,2.198 true 2.917,1.438 2.917,0.604 2.917,0.604 2.75,0.604 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.438,1.406 1.854,1.667 0.417,0.26 10 false A67 2.177,0.521 2.854,0.813 0.677,0.292 10 false CANH*b 2.208,2.115 2.885,2.406 0.677,0.292 10 false CANL*b 3.656,0.51 4.333,0.802 0.677,0.292 10 false CANH*c 3.656,2.115 4.333,2.406 0.677,0.292 10 false CANL*c
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 3 Junction Connector
*c to No. 4 CAN Junction Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-2 (CANH) - A67-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 junction connector
A67-5 (CANH) - A67-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction connector



Result:
Result Proceed to
OK A
NG (Line to No. 3 junction connector) B
NG (Line to No. 4 CAN junction connector) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

C

4.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the A67 No. 2 CAN junction connector.


b.

Disconnect the K127 No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C372332C18
1.323,1.344 1.813,1.615 0.49,0.271 3.583,1.427 3.583,0.583 3.583,0.583 3.396,0.583 true 3.594,1.708 3.594,2.167 3.594,2.167 3.406,2.167 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.417,1.406 1.833,1.667 0.417,0.26 10 false K127 2.844,0.5 3.521,0.792 0.677,0.292 10 false CANH*b 2.854,2.083 3.531,2.375 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 2 CAN Junction Connector


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K127-6 (CANH) - K127-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector



Result:
Result
OK
NG



OK

5.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

5.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the K127 No. 4 CAN junction connector.


b.

Disconnect the K128 No. 4 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C372332C19
1.323,1.344 1.813,1.615 0.49,0.271 3.583,1.427 3.583,0.583 3.583,0.583 3.396,0.583 true 3.594,1.708 3.594,2.167 3.594,2.167 3.406,2.167 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.417,1.406 1.833,1.667 0.417,0.26 10 false K128 2.844,0.5 3.521,0.792 0.677,0.292 10 false CANH*b 2.854,2.083 3.531,2.375 0.677,0.292 10 false CANL*b
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
K128-6 (CANH) - K128-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Airbag sensor assembly



Result:
Result
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

6.CHECK FOR OPEN IN CAN MAIN BUS LINES (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN MAIN BUS LINES (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.

Reconnect the K128 No. 4 CAN junction connector.


b.

Disconnect the K73 airbag sensor assembly connector.


c.
C369117C03
1.5,0.583 1.917,0.833 0.417,0.25 1.927,3.052 2.094,3.052 2.094,3.052 2.094,2.219 true 2.365,3.052 2.198,3.052 2.198,3.052 2.198,2.219 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.469,2.979 1.938,3.219 0.469,0.24 10 false CANH 2.448,2.958 2.917,3.198 0.469,0.24 10 false CANL 1.594,0.635 1.906,0.833 0.313,0.198 10 false K73
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K73-26 (CANH) - K73-27 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)