Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2017.09–2018.04
RM33A0E _56 Audio / Visual / Telematics _065374 NAVIGATION / MULTI INFO DISPLAY _0328126 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C0  GPS Antenna Connection Malfunction(short)  B15C1  GPS Antenna Connection Malfunction(break)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Connection Malfunction(short) Navigation antenna malfunction
·

Navigation antenna assembly

·

Antenna cord sub-assembly (for navigation antenna)

·

Navigation ECU


B15C1 GPS Antenna Connection Malfunction(break) Navigation antenna power source malfunction
·

Navigation antenna assembly

·

Antenna cord sub-assembly (for navigation antenna)

·

Navigation ECU



WIRING DIAGRAM

E362443E03
5.229,3.063 6.25,3.521 1.021,0.458 10 false Navigation ECU 0.583,1.26 2.625,1.677 2.042,0.417 10 false Navigation Antenna Assembly 0.417,3 4.021,3.229 3.604,0.229 10 false *: Antenna Cord Sub-assembly (for Navigation Antenna) 0.594,1.104 1.156,1.438 0.563,0.333 10 false A 5.24,2.896 5.802,3.229 0.563,0.333 10 false B 4.958,0.5 5.417,0.875 0.458,0.375 10 false 1 1.844,0.49 2.302,0.865 0.458,0.375 10 false 3 3.406,1.24 3.844,1.594 0.438,0.354 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the navigation ECU, always replace it with a new one. If a navigation ECU which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The navigation ECU may not operate normally.


·

Check that the antenna cord sub-assembly (for navigation antenna) is properly installed and does not have any sharp bends, pinching or loose connections before performing following procedure.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Navigation Antenna)
2.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Navigation Antenna)
a.

Remove the antenna cord sub-assembly (for navigation antenna).

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>ANTENNA CORD>REMOVAL


b.
E322997C03
0.5,1.188 0.917,1.438 0.417,0.25 0.656,3.479 1.073,3.729 0.417,0.25 1.927,3.76 2.344,3.344 false 1.854,1 2.271,0.583 false 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 2.354,3.177 2.667,3.375 0.313,0.198 10 false 1a 2.313,0.427 2.625,0.625 0.313,0.198 10 false 3a 0.656,1.229 0.969,1.427 0.313,0.198 10 false A 0.813,3.521 1.125,3.719 0.313,0.198 10 false B
*a Component without harness connected
(Antenna Cord Sub-assembly (for Navigation Antenna))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - B-1 Always Below 1 Ω
A-3a - B-1a Always Below 1 Ω
A-3 or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Navigation Antenna)

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

b.
E381436C05
1.219,1.177 1.615,0.771 false 1.115,1.198 1.427,1.396 0.313,0.198 10 false 3a 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Navigation Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 3a Always 50 to 500 Ω



Result:
Proceed to
OK
NG



OK

NG