Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328237 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Unable to Unlock Steering Wheel (Engine cannot Start)  


DESCRIPTION

The steering lock ECU (steering lock actuator or upper bracket assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the engine switch is turned on (IG) while shaking the steering wheel, as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to unlock steering wheel (Engine cannot start)
Smart Key
·

Unlock Request Receive

·

L Code Check

·

Steering Unlock


-

WIRING DIAGRAM

B463111E07
3.552,0.563 4.469,0.76 0.917,0.198 10 false from Battery 2.292,0.74 3.208,0.938 0.917,0.198 10 false STRG LOCK 5.354,3.354 6.885,3.854 1.531,0.5 10 false Certification ECU (Smart Key ECU Assembly) 0.625,4.375 2.615,4.594 1.99,0.219 10 false : LIN Communication Line 5.354,3.177 6.01,3.51 0.656,0.333 10 false K62 0.188,3.188 1.104,3.385 0.917,0.198 10 false K65 0.177,3.354 2.854,3.896 2.677,0.542 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 1.802,1.844 2.719,2.042 0.917,0.198 10 false IGE 1.698,2.281 2.615,2.479 0.917,0.198 10 false SLP1 1.76,2.75 2.677,2.948 0.917,0.198 10 false GND 2.156,0.458 2.646,0.708 0.49,0.25 10 false 7 5.771,2.729 6.26,2.948 0.49,0.219 10 false E 5.771,2.302 6.26,2.521 0.49,0.219 10 false SLP 5.76,1.823 6.25,2.042 0.49,0.219 10 false SLR+ 5.5,1.74 5.99,1.958 0.49,0.219 10 false 25 5.5,2.177 5.99,2.396 0.49,0.219 10 false 14 5.521,2.625 6.01,2.844 0.49,0.219 10 false 18 1.948,0.552 2.438,0.802 0.49,0.25 10 false B 2.146,1.719 2.635,1.969 0.49,0.25 10 false 3 2.146,2.177 2.635,2.427 0.49,0.25 10 false 4 2.146,2.625 2.635,2.875 0.49,0.25 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.


·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, confirm that the problem does not recur.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

If the steering lock ECU (steering lock actuator or upper bracket assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. This function prevents the engine from starting while the steering is locked. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch.



PROCEDURE

1.CHECK ENGINE SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:

OK:

Off → On (ACC) → On (IG) → Off




Result:
Proceed to
OK
NG



OK

2.CHECK INDICATOR

NG

2.CHECK INDICATOR
a.

With the engine switch on (IG), check that Steering Lock active is displayed on the multi-information display in the combination meter assembly.


Result:
Result Proceed to
Steering Lock active is displayed A
Steering Lock active is not displayed B



A

3.CHECK STEERING UNLOCK

B

4.CHECK FOR DTC
3.CHECK STEERING UNLOCK
a.

Turn the steering wheel left and right, and then press the engine switch.


b.

Check that the steering is unlocked.


Result:
Result Proceed to
The steering is unlocked A
The steering is not unlocked B



A

B

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Using the GTS, check if the certification ECU (smart key ECU assembly) DTC is output.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

5.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)

B

GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC

5.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock request is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of engine switch turned on (ACC) or on (IG), or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (engine switch not turned on (ACC) or on (IG), and engine start operation not performed)
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (L CODE CHECK)

NG

11.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
6.READ VALUE USING GTS (L CODE CHECK)
a.

Use the Data List to check if L code certification is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND GROUND)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND GROUND)
a.

Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C350527C75
1.5,0.969 1.917,1.229 0.417,0.26 0.917,2.917 1.167,2.917 1.167,2.917 1.167,1.948 true 2.5,2.917 2.25,2.917 2.25,2.917 2.25,1.948 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 0.781,2.823 1.094,2.99 0.313,0.167 10 false B 2.542,2.823 2.927,2.99 0.385,0.167 10 false GND 1.583,1.01 1.896,1.167 0.313,0.156 10 false K65
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K65-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K65-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Connect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Move the shift lever to P and turn the engine switch off.


c.

Check the signal waveform according to the condition(s) in the table below.

B478896C14
4,1.01 5.115,1.208 1.115,0.198 5,1.938 5.729,2.135 0.729,0.198 5.542,1.052 5.938,1.24 0.396,0.188 1.688,0.406 2.094,0.656 0.406,0.25 1.844,2.448 2.01,2.448 2.01,2.448 2.01,1.271 true 2.49,2.448 2.302,2.448 2.302,2.448 2.302,1.271 true 5.115,1.01 6.094,0.479 6.094,0.479 5.563,1.052 true 5.531,2.49 5.344,2.49 5.344,2.49 5.344,2.146 true 0.531,0.531 0.844,0.688 0.313,0.156 10 false *a 6.135,0.385 6.448,0.542 0.313,0.156 10 false *b 5.573,2.406 5.885,2.563 0.313,0.156 10 false *c 3.646,0.646 3.958,0.802 0.313,0.156 10 false *d 1.583,2.365 1.969,2.625 0.385,0.26 10 false IGE 2.531,2.375 2.917,2.635 0.385,0.26 10 false GND 6.156,1.969 6.542,2.229 0.385,0.26 10 false GND 1.771,0.448 2.125,0.635 0.354,0.188 10 false K65
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating *d Waveform


OK:
Tester Connection Condition Tool Setting Specified Condition
K65-3 (IGE) - K65-1 (GND) 2 V/DIV., 200 ms./DIV. Steering lock motor not operating → Operating → Not operating Pulse generation
(See waveform)


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.





Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
9.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K65-3 (IGE) - K62-25 (SLR+) Always Below 1 Ω
K65-3 (IGE) or K62-25 (SLR+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Connect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Connect the K62 certification ECU (smart key ECU assembly) connector.


c.
C350527C76
1.479,0.927 1.896,1.188 0.417,0.26 2.344,2.99 1.896,2.99 1.896,2.99 1.896,1.958 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.385,2.896 2.792,3.063 0.406,0.167 10 false IGE 1.552,0.969 1.865,1.125 0.313,0.156 10 false K65
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K65-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

11.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.
C350527C77
1.479,0.938 1.896,1.198 0.417,0.26 2.281,3 1.729,3 1.729,3 1.729,1.969 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.313,2.906 2.719,3.073 0.406,0.167 10 false SLP1 1.573,0.979 1.885,1.135 0.313,0.156 10 false K65
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K65-4 (SLP1) - Body ground Steering locked 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (STEERING UNLOCK)

NG

13.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
12.READ VALUE USING GTS (STEERING UNLOCK)
a.

Check that the steering is locked.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Steering lock ECU (steering lock actuator or upper bracket assembly) unlock confirmation status Unset or Set Unset: Unlock not confirmed
Set: Unlock confirmed
When Unset is displayed, the steering is not unlocked (the engine cannot be started).
Body Electrical > Entry&Start > Data List
Tester Display
Steering Unlock
50003 125 48
OK:

Set is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

13.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K65-4 (SLP1) - K62-14 (SLP) Always Below 1 Ω
K65-4 (SLP1) or K62-14 (SLP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.

for Manual Tilt and Manual Telescopic Steering Column:Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY

for Power Tilt and Power Telescopic Steering Column:Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY


b.

Perform registration.

HINT:

Refer to Service Bulletin.



c.

Turn the engine switch on (IG).


d.

Use the Data List to check if the steering lock request is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Status of steering unlock command from certification ECU (smart key ECU assembly) OK or NG OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of engine switch turned on (ACC) or on (IG), or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (engine switch not turned on (ACC) or on (IG), and engine start operation not performed)
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)