Home › Engine / Hybrid System › 2AR-FE (FUEL) › FUEL SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065325 2AR-FE FUEL _0328384 FUEL SYSTEM L

2AR-FE FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.



IGNITION SWITCH EXPRESSIONS


a.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



BEFORE WORKING ON FUEL SYSTEM


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



b.

Do not smoke or work near fire when handling the fuel system.


c.

Keep fuel away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

When discharging fuel system pressure by disconnecting the C/OPN relay:

i.

Remove the engine room relay block and junction block assembly cover.


ii.

Remove the C/OPN relay.


iii.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



iv.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P0171 (System Too Lean), P1603 (Engine Stall History), P1604 (Startability Malfunction) and P1605 (Rough Idling) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



v.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


vi.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



vii.

Install the C/OPN relay.


viii.

Install the engine room relay block and junction block assembly cover.



b.

When discharging fuel system pressure by disconnecting the fuel pump connector:

i.

Disconnect the rear center seat outer belt assembly.



ii.

Remove the rear seat cushion assembly.



iii.

Remove the rear seat cushion lock hook.



iv.
A401628C01
0.51,1.146 0.677,1.146 0.677,1.146 0.896,0.854 true 0.333,1.052 0.51,1.229 0.177,0.177 10 true *a
*a Protective Tape


Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.


v.
A405326

Disconnect the fuel pump connector.


vi.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



vii.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P0171 (System Too Lean), P1603 (Engine Stall History), P1604 (Startability Malfunction) and P1605 (Rough Idling) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



viii.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


ix.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



x.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


xi.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


xii.

Connect the fuel pump connector.


xiii.
A401707C01
0.802,0.302 0.958,0.302 0.958,0.302 1.125,0.5 true 0.615,0.219 0.792,0.385 0.177,0.167 10 true *a
*a Butyl Tape Adhesion Area


Install the rear floor service hole cover with new butyl tape.

NOTICE:

Securely install the rear floor service hole cover.



xiv.

Install the rear seat cushion lock hook.



xv.

Install the rear seat cushion assembly.



xvi.

Connect the rear center seat outer belt assembly.





FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel pump tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Quick Type A:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A401631C01
0,0 0,0 false
V100135

Open
V100136

Pull


Open the cover of the No. 1 fuel pipe clamp and remove the No. 1 fuel pipe clamp from the fuel tube connector.


ii.

Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.


iii.
A403898C01
1.833,2.344 2.073,2.031 2.073,2.031 2.219,2.031 false 2.271,1.948 2.583,2.104 0.313,0.156 10 false *a
*a Retainer
V100135

Retainer Holding Position
V100136

Pull up


While holding the retainer at the positions shown in the illustration, pull up the retainer to disengage the lock claws.


iv.
A403899C01
1.167,0.354 1.313,0.354 1.313,0.354 1.625,0.646 false 1.896,1.948 2.104,1.573 2.104,1.573 2.25,1.573 false 1.979,3.188 2.073,2.938 2.073,2.938 2.219,2.938 false 1.354,3.333 1.604,3.333 1.604,3.333 1.604,3.594 false 2.125,3.885 2.281,4.302 2.281,4.302 2.396,4.302 false 0.833,4.177 0.833,3.917 true 1.875,4.26 1.875,4.063 false 1.479,3.594 1.479,3.333 false 1,0.26 1.313,0.417 0.313,0.156 10 false *a 1.198,3.24 1.51,3.396 0.313,0.156 10 false *b 1.802,4.292 2.115,4.448 0.313,0.156 10 false *c 0.75,4.208 1.063,4.365 0.313,0.156 10 false *d 2.448,4.208 2.76,4.365 0.313,0.156 10 false *e 2.302,1.49 2.615,1.646 0.313,0.156 10 false *a 2.271,2.854 2.583,3.01 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Retainer Holding Position
V100136

Pull out
V100137

Pull off


Pull up the retainer while holding it at the positions shown in the illustration and pull off the fuel tube connector.


v.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




vi.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Quick Type A:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A393281C01
1.167,2.354 1.448,2.354 false 1,2.25 1.313,2.406 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Install the No. 1 fuel pipe clamp to the fuel tube connector and close the cover of the No. 1 fuel pipe clamp.




d.

Quick Type B:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A363273C01
1.958,2.177 1.75,2.177 false 2.042,2.677 1.823,2.885 1.823,2.885 1.698,2.885 true 1.979,3.677 1.979,3.271 1.979,3.271 1.719,3.271 false 2.844,2.854 2.708,2.854 2.708,2.854 2.521,2.667 true 2.719,3.208 2.552,3.208 2.552,3.208 2.375,3.521 false 2.865,4.375 2.729,4.375 2.729,4.375 2.615,4.021 false 2.031,4.135 2.031,4.375 false 1.573,2.073 1.885,2.229 0.313,0.156 10 false *a 2.917,4.302 3.229,4.458 0.313,0.156 10 false *b 1.958,4.385 2.271,4.542 0.313,0.156 10 false *c 1.552,3.188 1.865,3.344 0.313,0.156 10 false *d 1.531,2.792 1.844,2.948 0.313,0.156 10 false *e 2.771,3.125 3.083,3.281 0.313,0.156 10 false *a 2.896,2.771 3.208,2.927 0.313,0.156 10 false *e
*a Retainer
*b Fuel Pipe
*c Fuel Tube Connector
*d O-ring
*e Claw
V100135

Pull
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Quick Type B:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A366419C01
2.271,3 2.365,3 2.365,3 2.469,2.885 true 2.198,2.406 2.427,2.406 false 2.979,2.885 3.125,3 3.125,3 3.188,3 true 2.031,2.313 2.344,2.469 0.313,0.156 10 false *a 2.094,2.917 2.406,3.073 0.313,0.156 10 false *b 3.229,2.917 3.427,3.094 0.198,0.177 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to engage the 2 claws.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




f.

Quick Type C:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A318103C02
0.698,2.625 0.854,2.625 0.854,2.625 1.042,3.135 false 0.24,3.021 0.375,3.021 0.375,3.021 0.51,3.333 false 0.99,4.021 0.99,3.75 false 2.146,1.844 2.417,1.844 false 1.865,3.906 1.865,3.583 false 2.49,3.25 2.542,2.938 2.542,2.938 2.656,2.938 false 1.688,3.594 1.688,3.906 1.688,3.906 2.208,3.906 false 2.146,1.573 2.417,1.573 false 2.865,1.563 3.135,1.563 false 1.969,1.76 2.281,1.917 0.313,0.156 10 false *a 0.063,2.948 0.375,3.104 0.313,0.156 10 false *b 2.708,2.865 3.021,3.021 0.313,0.156 10 false *c 0.906,4.052 1.219,4.208 0.313,0.156 10 false *d 2.25,3.833 2.563,3.99 0.313,0.156 10 false *e 0.521,2.542 0.833,2.698 0.313,0.156 10 false *a 3.198,1.5 3.375,1.677 0.177,0.177 10 false *f 2,1.5 2.177,1.677 0.177,0.177 10 false *f
*a Retainer
*b Fuel Pipe
*c Nylon Tube
*d Fuel Tube Connector
*e O-ring
*f Claw
V100135

Push
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Quick Type C:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A303816C02
1.958,1.531 2.365,1.531 false 1.958,1.281 2.365,1.281 false 2.781,1.271 3.188,1.271 false 1.781,1.448 2.094,1.604 0.313,0.156 10 false *a 1.823,1.198 2.135,1.354 0.313,0.156 10 false *b 3.24,1.208 3.427,1.365 0.188,0.156 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to engage the 2 claws.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




h.

Metallic Type:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A405325C01
2.563,0.948 2.677,1.156 2.677,1.156 2.771,0.938 false 2.594,1.167 2.906,1.323 0.313,0.156 10 false *a
*a Claw


Disengage the 2 claws to remove the No. 2 fuel pipe clamp.


ii.
A300491N03
0.479,1.427 0.479,1.198 0.479,1.198 0.792,1.052 false 2.469,1.25 2.615,0.906 2.615,0.906 2.792,0.906 false 2.854,0.844 3.177,1.042 0.323,0.198 10 false SST 0.365,1.469 0.823,1.667 0.458,0.198 10 false SST

Install SST (fuel hose puller) to the fuel tube connector as shown in the illustration.

SST
09268-21011  


iii.
A300492C07
2.188,1.396 2.49,1.698 2.49,1.698 2.688,1.698 false 0.396,0.281 0.802,0.281 0.802,0.281 0.802,0.427 true 0.531,0.604 0.531,0.281 false 1.26,1.24 1.26,0.729 1.26,0.729 1.073,0.729 true 0.896,0.958 1.26,0.958 false 0.229,0.198 0.479,0.385 0.25,0.188 10 false *a 2.74,1.646 3.135,1.844 0.396,0.198 10 false SST 1.177,1.24 1.49,1.396 0.313,0.156 10 false *a
*a Retainer (4 places)


Turn SST (fuel hose puller), align the retainers inside the fuel tube connector with the SST (fuel hose puller) chamfers and insert SST (fuel hose puller) into the fuel tube connector.


iv.

Mount the retainer of the fuel tube connector onto the chamfered part of SST (fuel hose puller).


v.
A076220C16
2.26,1.573 2.26,1.875 false 0.594,1.375 0.594,1.708 false 1.396,0.875 1.125,0.438 1.125,0.438 1.594,0.875 false 2.917,1.323 2.917,1.531 false 2.156,0.771 2.281,0.438 2.281,0.438 2.417,0.438 false 0.948,0.323 1.25,0.563 0.302,0.24 10 false *b 2.479,0.354 2.833,0.563 0.354,0.208 10 false *a 2.844,1.573 3.073,1.771 0.229,0.198 10 false *e 0.51,1.74 0.719,1.969 0.208,0.229 10 false *c 2.177,1.917 2.385,2.115 0.208,0.198 10 false *d
*a Retainer
*b O-ring
*c Nylon Tube
*d Fuel Tube Connector
*e Fuel Pipe


Slide SST (fuel hose puller) and the fuel tube connector together until they make a "click" sound, and then disconnect the fuel tube connector.

NOTICE:
·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




vi.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



i.

Metallic Type:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A304571C01
1.813,1.229 1.969,1.427 0.156,0.198 10 false .
V100135

Pull


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound.

HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Engage the 2 claws to install a new No. 2 fuel pipe clamp.




j.
A289951C03
2.333,0.427 2.521,0.427 2.521,0.427 2.823,0.74 false 0.917,1.615 1.104,1.615 1.104,1.615 1.365,1.333 false 1.708,1.281 1.906,1.594 1.906,1.594 2.052,1.594 false 2.156,0.354 2.448,0.594 0.292,0.24 10 *a 2.115,1.531 2.438,1.792 0.323,0.26 10 *b 0.698,1.563 1,1.823 0.302,0.26 10 *c
*a Fuel Tube Connector
*b Nylon Tube
*c Ethylene Propylene Diene Monomer (EPDM) Rubber Protector


Observe the following precautions when handling a nylon tube:

NOTICE:
·

Do not twist the nylon tube of the fuel tube connector or fuel tube connector when connecting it.

·

Do not remove the Ethylene Propylene Diene Monomer (EPDM) rubber protector on the outside of the nylon tube.

·

Do not bend, twist, pinch or kink the nylon tube.





FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


NOTICE:
·
A405327C01
0.646,1.365 1.438,1.365 true 0.469,1.281 0.781,1.438 0.313,0.156 10 false *a
*a Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION