1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
Check fuel pump operation.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
2.CHECK FUEL PRESSURE
Discharge fuel system pressure.
Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SYSTEM>PRECAUTION
Measure the battery voltage.
11 to 14 V
Disconnect the cable from the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
|
Open |
|
Pull |
Open the cover of the No. 1 fuel pipe clamp and remove the No. 1 fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SYSTEM>PRECAUTION
| *1 | Fuel Tube Sub-assembly (Vehicle Side) |
| *a | SST (Hose Band) |
| *b | SST (T-joint) |
| *c | SST (Gauge) |
| *d | SST (Hose Joint) |
| *e | SST (Hose) |
| *f | SST (Fuel Tube Connector) |
| *g | Fuel Pipe (Vehicle Side) |
Install SST (EFI fuel pressure gauge) as shown in the illustration.
Wipe up any spilled fuel.
Connect the cable to the negative (-) battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
Measure the fuel pressure.
304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)
If the fuel pressure is less than the standard, check the fuel hoses and their connections, fuel pump, fuel filter and fuel pressure regulator assembly.
If the result is not as specified, replace the fuel pressure regulator assembly.
Disconnect the GTS from the DLC3.
Start the engine.
Measure the fuel pressure at idle.
304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)
Refer to Standard Idle Speed.
Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
Stop the engine.
Check that the fuel pressure remains as specified for 5 minutes.
147 kPa (1.5 kgf/cm2, 21 psi) or more
If the result is not as specified, check the fuel pump, fuel pressure regulator assembly and/or fuel injector assemblies.
After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent fuel from spraying.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Connect the fuel tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SYSTEM>PRECAUTION
Install the No. 1 fuel pipe clamp to the fuel tube connector and close the cover of the No. 1 fuel pipe clamp.
Inspect for fuel leaks.
Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION