Home › Engine / Hybrid System › 2AR-FE EMISSION CONTROL › EMISSION CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065326 2AR-FE EMISSION CONTROL _0328631 EMISSION CONTROL SYSTEM G

2AR-FE EMISSION CONTROL  EMISSION CONTROL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL CUT OPERATION

a.

Start the engine.


b.

Warm up the engine.


c.

Increase the engine speed to approximately 3500 rpm.


d.
A292050C07
1.656,1.156 1.833,1.427 1.833,1.427 2.104,1.427 true 1.135,0.615 1.594,0.615 1.594,0.615 1.75,0.865 true 0.938,0.521 1.156,0.719 0.219,0.198 10 true *1 2.167,1.375 2.385,1.573 0.219,0.198 10 true *a
*1 Fuel Injector Assembly
*a Sound Scope


Use a sound scope to check for fuel injector assembly operating sounds.


e.

When the accelerator pedal is fully released, check that fuel injector assembly operating sounds stop momentarily and then resume.

Standard:
Item Specified Condition
Fuel injection restart engine speed 1400 rpm


If the result is not as specified, check the fuel injector assemblies, wire harness and ECM.


Hide 2.VISUALLY CHECK HOSES, CONNECTIONS AND GASKETS

a.

Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

NOTICE:
·

Detachment or other problems with the engine oil level dipstick, oil filler cap sub-assembly, ventilation hose or other components may cause the engine to run improperly.

·

Air suction caused by disconnections, looseness or cracks in any part of the air induction system between the throttle body with motor assembly and cylinder head sub-assembly will cause engine failure or engine malfunctions.



If any defects are found, replace parts as necessary.


Hide 3.INSPECT EVAPORATIVE EMISSION CONTROL SYSTEM

a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.
A407078

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the purge valve (purge VSV).


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

f.

Check that vacuum occurs at the purge valve (purge VSV) port.


g.

If vacuum does not occur, check the following items.

·

Purge valve (purge VSV)

·

Clogging in the No. 2 fuel vapor feed hose that connects the intake manifold and purge valve (purge VSV)



h.

Exit Active Test mode and connect the No. 1 fuel vapor feed hose assembly to the purge valve (purge VSV) and slide the clip to secure it.

Click hereEngine / Hybrid System>2AR-FE EMISSION CONTROL>PURGE VALVE>INSTALLATION

If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.


i.

Enter the following menus: Powertrain / Engine and ECT / Data List / EVAP Purge VSV.

Powertrain > Engine and ECT > Data List
Tester Display
EVAP Purge VSV
50003 234 217

j.

Warm up the engine and drive the vehicle.


k.

Confirm that the purge valve (purge VSV) opens.

If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.