Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM33A0E _58 Vehicle Interior _065378 DOOR LOCK _0329089 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch assembly and activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B417906E09
1.104,0.76 1.26,0.958 0.156,0.198 10 false 5 1.281,0.76 1.781,0.979 0.5,0.219 10 false E 2.792,0.49 2.948,0.688 0.156,0.198 10 false 2 2.781,1.042 3.031,1.25 0.25,0.208 10 false 4 2.51,0.49 2.771,0.708 0.26,0.219 10 false UL 2.594,1.042 2.75,1.26 0.156,0.219 10 false L 4.073,0.396 4.323,0.604 0.25,0.208 10 false 39 4.063,0.594 4.313,0.802 0.25,0.208 10 false 3A 4.063,0.938 4.313,1.146 0.25,0.208 10 false 16 4.052,1.135 4.302,1.344 0.25,0.208 10 false 3B 5.26,0.5 5.51,0.708 0.25,0.208 10 false 22 5.271,1.042 5.521,1.25 0.25,0.208 10 false 20 5.5,0.583 5.854,0.813 0.354,0.229 10 false UL1 5.5,1.135 5.854,1.365 0.354,0.229 10 false L1 3.802,1.542 5.406,1.938 1.604,0.396 10 false Instrument Panel Junction Block Assembly 5.25,2.156 6.927,2.542 1.677,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 5.24,2.01 5.531,2.219 0.292,0.208 10 false MB 1.063,1.583 2.188,1.813 1.125,0.229 10 false N4 1.063,1.75 3.083,2.167 2.021,0.417 10 false Door Control Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*

*: w/ Smart Entry and Start System




PROCEDURE

1.READ VALUE USING GTS (Door Lock SW-Lock, Door Lock SW-Unlock)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch assembly lock signal OFF or ON OFF: Lock side of door control switch assembly not pushed
ON: Lock side of door control switch assembly pushed
-
Door Lock SW-Unlock Door control switch assembly unlock signal OFF or ON OFF: Unlock side of door control switch assembly not pushed
ON: Unlock side of door control switch assembly pushed
-
Body Electrical > Main Body > Data List
Tester Display
Door Lock SW-Lock
Door Lock SW-Unlock
50003 123 17,18

OK:

The GTS indicates ON or OFF according to the switch operation shown in the table.


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT DOOR CONTROL SWITCH ASSEMBLY
2.INSPECT DOOR CONTROL SWITCH ASSEMBLY
a.

Remove the door control switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL


b.

Inspect the door control switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE DOOR CONTROL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A and 3B instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N4-2 (UL) - 3A-39 Always Below 1 Ω
N4-4 (L) - 3B-16 Always Below 1 Ω
N4-5 (E) - Body ground Always Below 1 Ω
3A-39 or N4-2 (UL) - Other terminals and body ground Always 10 kΩ or higher
3B-16 or N4-4 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU).

B417872C07
2.021,0.823 2.396,1.083 0.375,0.26 5.427,0.458 5.802,0.719 0.375,0.26 5.375,2.177 5.75,2.438 0.375,0.26 2.5,2.26 2.427,2.938 false 2.719,2.271 2.792,2.948 false 0.188,0.177 0.5,0.375 0.313,0.198 10 false *a 2.104,0.865 2.417,1.063 0.313,0.198 10 false MB 5.469,2.219 5.781,2.417 0.313,0.198 10 false 3B 2.333,2.979 2.646,3.177 0.313,0.198 10 false L1 2.76,3 3.208,3.188 0.448,0.188 10 false UL1 5.531,0.5 5.844,0.698 0.313,0.198 10 false 3A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-22 (UL1) - 3A-39 Always Below 1 Ω
MB-20 (L1) - 3B-16 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY