Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065378 DOOR LOCK _0329092 KEY REMINDER WARNING SYSTEM U

DOOR LOCK  KEY REMINDER WARNING SYSTEM  TERMINALS OF ECU  


CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B472410N47
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.302,6.198 5.74,6.448 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 5.385,4.615 5.823,4.865 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 0.531,2.49 0.531,2.323 0.531,2.323 0.865,2.323 false 3.469,7.677 3.781,7.875 0.313,0.198 10 false MB 4.292,0.219 4.604,0.417 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false K51 2.052,1.479 2.365,1.677 0.313,0.198 10 false K52 2.052,1.802 2.365,2 0.313,0.198 10 false K53 0.875,1.073 1.188,1.271 0.313,0.198 10 false 3D 0.875,1.656 1.188,1.854 0.313,0.198 10 false 3C 0.885,2.021 1.198,2.219 0.313,0.198 10 false 3E 5.854,1.146 6.167,1.344 0.313,0.198 10 false 3B 5.854,1.76 6.167,1.958 0.313,0.198 10 false 3A 1.229,3.281 1.542,3.479 0.313,0.198 10 false K53 3.271,3.25 3.583,3.448 0.313,0.198 10 false K52 5.542,3.24 5.854,3.438 0.313,0.198 10 false K51 1.833,4.604 2.146,4.802 0.313,0.198 10 false 3A 1.24,6.198 1.552,6.396 0.313,0.198 10 false 3C 3.813,6.156 4.125,6.354 0.313,0.198 10 false 3D 5.427,6.229 5.74,6.427 0.313,0.198 10 false 3F 6.448,6.229 6.76,6.427 0.313,0.198 10 false 3E 5.521,4.646 5.833,4.844 0.313,0.198 10 false 3B 0.458,2.531 0.854,2.76 0.396,0.229 10 false 3F

a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
MB-11 (GND1) - Body ground - - Ground Always Below 1 Ω -
MB-30 (ACC) - Body ground - Input ACC power supply Ignition switch ACC 11 to 14 V ACC SW
Ignition switch off Below 1 V
MB-31 (BECU) - Body ground - Input Battery power supply Always 11 to 14 V -
MB-32 (IG) - Body ground - Input IG power supply Ignition switch ON 11 to 14 V IG SW
Ignition switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


e.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Input/Output Terminal Description Condition Specified Condition Related Data List Item
K52-1 (FLCY) - Body ground W- Body ground Input Front door courtesy light switch (for LH) input Front door LH open → closed Below 1 V → 11 to 14 V FL Door Courtesy SW
3A-41 (KSW) - Body ground GR - Body ground Input Key unlock warning switch input No key in ignition key cylinder → Key in ignition key cylinder 11 to 14 V → Below 1 V Key Unlock Warning SW