Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065378 DOOR LOCK _0329092 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the main body ECU (multiplex network body ECU) sends an unlock warning switch signal and driver door courtesy light switch signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM

B364847E08
0.927,0.688 1.24,0.885 0.313,0.198 10 false R5 0.948,1.833 1.26,2.031 0.313,0.198 10 false K31 0.927,0.833 2.552,1.25 1.625,0.417 10 false Front Door Courtesy Light Switch Assembly (for LH) 0.938,2 2.438,2.417 1.5,0.417 10 false Unlock Warning Switch Assembly 2.313,1.521 2.5,1.719 0.188,0.198 10 false 1 1.104,1.521 1.292,1.719 0.188,0.198 10 false 2 2.313,0.354 2.5,0.552 0.188,0.198 10 false 1 3.052,1.427 3.365,1.625 0.313,0.198 10 false 41 4.031,0.271 4.219,0.49 0.188,0.219 10 false 1 4.031,1.417 4.198,1.625 0.167,0.208 10 false 3 3.042,1.635 3.354,1.833 0.313,0.198 10 false 3A 3.969,1.635 4.281,1.833 0.313,0.198 10 false MB 3.948,0.479 4.26,0.677 0.313,0.198 10 false K52 4.354,1.635 4.927,1.875 0.573,0.24 10 false KSW 4.354,0.479 4.927,0.719 0.573,0.24 10 false FLCY 5.875,2.708 7.073,3.177 1.198,0.469 10 false Combination Meter Assembly 4.292,2.708 5.448,3.219 1.156,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 2.635,2.458 4.25,2.885 1.615,0.427 10 false Instrument Panel Junction Block Assembly 0.865,3.354 2.615,3.594 1.75,0.24 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

The key reminder warning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the key reminder warning system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (Buzzer Operation)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Operation (800Hz, Vol L, W/ Damping) Combination meter buzzer
·

Frequency: 800Hz

·

Volume: Large

·

Fading tone


ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Buzzer Operation (800Hz, Vol L, W/ Damping)
50004 409 13

Result:
Result Proceed to
Combination meter buzzer sounds A
Combination meter buzzer does not sound B



A

2.READ VALUE USING GTS (FL Door Courtesy SW)

B

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (FL Door Courtesy SW)
a.

Enter the following menus: Body Electrical / Main Body / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Courtesy SW Front door courtesy light switch assembly (for LH) signal OFF or ON OFF: Front door LH closed
ON: Front door LH open
-
Body Electrical > Main Body > Data List
Tester Display
FL Door Courtesy SW
50003 123 199
OK:

The GTS indicates ON or OFF according to the driver door conditions shown in the table.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (Key Unlock Warning SW)

NG

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for LH)
3.READ VALUE USING GTS (Key Unlock Warning SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal OFF or ON OFF: No key in ignition key cylinder
ON: Key in ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

The GTS indicates ON or OFF according to whether the key is in the ignition key cylinder.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-41 - K31-1 Always Below 1 Ω
K31-2 - Body ground Always Below 1 Ω
K31-1 or 3A-41 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B472423C01
1.917,0.917 2.302,1.219 0.385,0.302 5.406,0.635 5.802,0.938 0.396,0.302 0.781,2.177 0.531,2.177 0.531,2.177 0.531,1.594 false 5.521,0.719 5.833,0.917 0.313,0.198 10 false 3A 2.01,0.969 2.323,1.167 0.313,0.198 10 false MB 0.875,2.083 1.333,2.281 0.458,0.198 10 false KSW 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-41 - MB-3 (KSW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for LH)
a.

Remove the front door courtesy light switch assembly (for LH).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly (for LH).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for LH) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for LH)

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for LH) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K52 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-1 - K52-1 (FLCY) Always Below 1 Ω
R5-1 or K52-1 (FLCY) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR