Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2017.09–2021.02
RM33A0E _58 Vehicle Interior _065378 DOOR LOCK _0329089 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  Collision Door Lock Release Function does not Operate  


DESCRIPTION

When an impact is detected, a relay inside the door control battery is operated to switch the power source of the door lock with motor assemblies from the vehicle battery to the door control battery.

WIRING DIAGRAM

B399814E05
0.448,4.115 3.51,4.313 3.063,0.198 10 false Door Control Battery 0.448,3.948 3.51,4.146 3.063,0.198 10 false K58 1.104,3.333 4.167,3.531 3.063,0.198 10 false ACTG 1.333,1.604 4.396,1.802 3.063,0.198 10 false IG 1.604,1.49 4.667,1.688 3.063,0.198 10 false 8 1.604,3.219 4.667,3.417 3.063,0.198 10 false 9 2.469,1.479 5.531,1.677 3.063,0.198 10 false 30 5.229,3.229 6.594,3.573 1.365,0.344 10 false 9 2.865,1.76 5.927,1.958 3.063,0.198 10 false ECU-IG1 NO. 4 4.031,1.594 5,2.083 0.969,0.49 10 false from IG1-NO. 1 Relay 2.323,2.427 5.188,2.635 2.865,0.208 10 false Instrument Panel Junction Block Assembly 2.302,2.281 5.365,2.479 3.063,0.198 10 false 3B 5.198,3.938 7.156,4.229 1.958,0.292 10 false K52 5.198,4.104 6.865,4.51 1.667,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.417,3.333 7.115,3.563 1.698,0.229 10 false ACTG

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Before performing the inspection, check that DTC B1243 is not output.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DOOR LOCK OPERATION

OK:

All doors lock and unlock normally.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K58 door control battery connector.


b.

Disconnect the K52 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K58-9 (ACTG) - K52-9 (ACTG) Always Below 1 Ω
K58-9 (ACTG) or K52-9 (ACTG) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K58-8 (IG) - 3B-30 Always Below 1 Ω
K58-8 (IG) or 3B-30 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG1-NO. 1 RELAY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IG1-NO. 1 RELAY POWER SOURCE)
a.

Reconnect the 3B instrument panel junction block assembly connector.


b.
B495245C02
1.302,0.469 1.76,0.719 0.458,0.25 0.146,0.167 0.458,0.365 0.313,0.198 10 false *a 1.417,0.51 1.729,0.708 0.313,0.198 10 false 3B
*a Component with harness connected
(Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3B-30 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE DOOR CONTROL BATTERY

NG

GO TO LIGHTING SYSTEM (IG Signal Circuit)

5.REPLACE DOOR CONTROL BATTERY
a.

Replace the door control battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL BATTERY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DOOR CONTROL BATTERY
6.CHECK DOOR CONTROL BATTERY
a.

OK:

Collision detection door lock function operates normally.


Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL BATTERY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)