Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0329531 LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System)  Automatic High Beam Switch Indicator does not Come ON  


DESCRIPTION

When the automatic high beam system is on, the main body ECU (multiplex network body ECU) illuminates the auto high beam switch indicator.

WIRING DIAGRAM

E367187E03
3.302,1.646 4.875,1.927 1.573,0.281 10 false Auto High Beam Switch 3.313,1.5 3.677,1.677 0.365,0.177 10 false K50 3.104,0.948 3.469,1.125 0.365,0.177 10 false IND+ 2.927,0.948 3.292,1.125 0.365,0.177 10 false 3 4.604,0.969 5.031,1.177 0.427,0.208 10 false AZBI 4.99,0.948 5.354,1.125 0.365,0.177 10 false 4 5.823,0.938 6.25,1.146 0.427,0.208 10 false AHID 5.49,2.073 7.135,2.521 1.646,0.448 10 false Main Body ECU (Multiplex Network Body ECU) 5.583,0.948 5.948,1.125 0.365,0.177 10 false 23 5.49,1.906 5.854,2.083 0.365,0.177 10 false K51 1.917,1.219 3.49,1.5 1.573,0.281 10 false ECU-B NO. 2 0.375,1.052 1.948,1.333 1.573,0.281 10 false from AM2 Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Automatic High Beam Switch Light Auto high beam switch indicator light OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Automatic High Beam Switch Light
50004 123 74
OK:

Auto high beam switch indicator light illuminates.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT AUTO HIGH BEAM SWITCH
2.INSPECT AUTO HIGH BEAM SWITCH
a.

b.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - AUTO HIGH BEAM SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - AUTO HIGH BEAM SWITCH)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K50-3 (IND+) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K50-4 (AZBI) - K51-23 (AHID) Always Below 1 Ω
K50-4 (AZBI) or K51-23 (AHID) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR