Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil assembly (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil assembly (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil assembly (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil assembly (No. 4 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF1) signal to the ECM, for each cylinder ignition.

A288665E03
4.5,0.781 4.417,0.365 4.417,0.365 4.333,0.365 true 5.365,0.531 5.583,0.406 5.583,0.406 5.719,0.406 true 0.469,0.875 2.26,1.073 1.792,0.198 10 Crankshaft Position Sensor 0.448,2.677 2.24,2.875 1.792,0.198 10 Camshaft Position Sensor 0.323,3.708 2.25,4.406 1.927,0.698 10 Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, Throttle Position Sensor, etc.) 3.031,0.823 3.385,1 0.354,0.177 10 IGT1 3.031,1.135 3.385,1.313 0.354,0.177 10 IGF1 5.115,0.073 6.438,0.26 1.323,0.188 10 from Battery 3.927,0.271 4.417,0.5 0.49,0.229 10 Igniter 5.76,0.333 7.146,0.896 1.385,0.563 10 Ignition Coil Assembly (No. 1 Cylinder) 5.74,1.25 6.875,1.469 1.135,0.219 10 No. 1 Spark Plug 5.74,2.469 6.875,2.688 1.135,0.219 10 No. 2 Spark Plug 5.719,3.781 6.854,4 1.135,0.219 10 No. 3 Spark Plug 5.75,5.104 6.885,5.323 1.135,0.219 10 No. 4 Spark Plug 3,2.156 3.354,2.333 0.354,0.177 10 IGT2 3,3.479 3.354,3.656 0.354,0.177 10 IGT3 3.031,4.792 3.385,4.969 0.354,0.177 10 IGT4 3.813,2.771 6.271,2.958 2.458,0.188 10 Ignition Coil Assembly (No. 2 Cylinder) 3.823,4.094 6.281,4.281 2.458,0.188 10 Ignition Coil Assembly (No. 3 Cylinder) 3.781,5.375 6.24,5.563 2.458,0.188 10 Ignition Coil Assembly (No. 4 Cylinder) 2.854,5.323 3.208,5.5 0.354,0.177 10 ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil assembly

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

No. 2 ignition coil assembly

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 3 ignition coil assembly

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF1 signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

No. 4 ignition coil assembly

·

No. 1 integration relay

·

ECM


Comes on DTC stored

A289263E01
2.844,0.857 3.210,1.059 0.366,0.202 10 GND 2.844,1.502 3.175,1.704 0.331,0.202 10 GND 0.058,0.41 0.435,0.915 0.376,0.504 10 CH1 (IGT) 0.021,1.193 0.440,1.551 0.419,0.358 10 CH2 (IGF1) 0.03,0.036 0.574,0.213 0.545,0.177 10 2 V/DIV. 1.154,1.844 1.905,1.988 0.751,0.145 10 20 ms./DIV.

Reference: Inspection using an oscilloscope

HINT:

While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.


ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

A212405E37
1.781,1.646 2.177,1.823 0.396,0.177 10 false ECM 2.958,1.302 3.229,1.49 0.271,0.188 10 false IGT 2.917,1.729 3.271,1.885 0.354,0.156 10 false IGF1 4.156,1.51 4.594,1.656 0.438,0.146 10 false Igniter 5.396,1.344 6.167,1.521 0.771,0.177 10 false Ignition Coil 4.469,2.354 5.875,2.542 1.406,0.188 10 false Ignition Coil Assembly 0.208,3.115 1.146,3.448 0.938,0.333 10 false Ignition Signal (IGT) 1.646,3.542 2.135,3.729 0.49,0.188 10 false Normal 1.385,3.948 2.156,4.135 0.771,0.188 10 false Malfunction 0.188,3.896 1.156,4.417 0.969,0.521 10 false Ignition Confirmation Signal (IGF1) 3.635,4.51 4.49,4.688 0.854,0.177 10 false Circuit Open 5.948,4.969 6.313,5.167 0.365,0.198 10 false Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter (Cylinder 1 to 4)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 10 seconds or more [A].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0351, P0352, P0353 or P0354.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A412706E01
0.094,0.073 4.99,0.271 4.896,0.198 12 false w/ Smart Entry and Start System: 0.51,5.583 1.583,5.781 1.073,0.198 10 false Battery 0.344,4.469 1.417,4.667 1.073,0.198 10 false FL MAIN 1.438,1.615 2.25,1.885 0.813,0.271 10 false IG2 NO. 1 0.458,0.927 1.292,1.188 0.833,0.26 10 false IG2-MAIN 1.271,0.635 1.427,0.833 0.156,0.198 10 false 5 2.115,0.635 2.271,0.833 0.156,0.198 10 false 3 1.302,1.135 1.458,1.333 0.156,0.198 10 false 2 2.115,1.135 2.271,1.333 0.156,0.198 10 false 1 2.573,0.917 3.031,1.115 0.458,0.198 10 false INJ 2.24,3.25 2.552,3.448 0.313,0.198 10 false 17 1,3.958 1.458,4.156 0.458,0.198 10 false K62 1.813,3.396 2.427,3.594 0.615,0.198 10 false IG1D 1.281,3.958 2.802,4.667 1.521,0.708 10 false Certification ECU (Smart Key ECU Assembly) 3.708,0.615 3.865,0.813 0.156,0.198 10 false 1 3.75,2.25 3.906,2.448 0.156,0.198 10 false 1 3.771,3.854 3.927,4.052 0.156,0.198 10 false 1 3.719,5.365 3.875,5.563 0.156,0.198 10 false 1 3.74,0.948 3.896,1.146 0.156,0.198 10 false 4 3.729,2.552 3.885,2.75 0.156,0.198 10 false 4 3.76,4.167 3.917,4.365 0.156,0.198 10 false 4 3.74,5.771 3.896,5.969 0.156,0.198 10 false 4 4.958,0.615 5.115,0.813 0.156,0.198 10 false 3 4.969,2.229 5.125,2.427 0.156,0.198 10 false 3 4.948,3.802 5.104,4 0.156,0.198 10 false 3 4.979,5.354 5.135,5.552 0.156,0.198 10 false 3 4.979,0.969 5.135,1.167 0.156,0.198 10 false 2 4.979,2.563 5.135,2.76 0.156,0.198 10 false 2 4.969,4.156 5.125,4.354 0.156,0.198 10 false 2 4.979,5.719 5.135,5.917 0.156,0.198 10 false 2 3.948,0.771 4.26,0.969 0.313,0.198 10 false +B 3.948,2.365 4.26,2.563 0.313,0.198 10 false +B 3.958,3.969 4.271,4.167 0.313,0.198 10 false +B 3.927,5.479 4.24,5.677 0.313,0.198 10 false +B 3.958,1.094 4.417,1.292 0.458,0.198 10 false GND 3.938,2.698 4.396,2.896 0.458,0.198 10 false GND 3.958,4.281 4.417,4.479 0.458,0.198 10 false GND 3.948,5.896 4.406,6.094 0.458,0.198 10 false GND 4.625,1.063 5.083,1.26 0.458,0.198 10 false IGF 4.615,2.677 5.073,2.875 0.458,0.198 10 false IGF 4.573,4.281 5.031,4.479 0.458,0.198 10 false IGF 4.583,5.875 5.042,6.073 0.458,0.198 10 false IGF 4.51,2.365 5.125,2.563 0.615,0.198 10 false IGT2 4.563,0.76 5.177,0.958 0.615,0.198 10 false IGT1 4.542,3.958 5.156,4.156 0.615,0.198 10 false IGT3 4.531,5.49 5.146,5.688 0.615,0.198 10 false IGT4 3.594,1.458 3.906,1.656 0.313,0.198 10 false C1 3.594,1.625 5.469,1.969 1.875,0.344 10 false No. 1 Ignition Coil Assembly 3.604,3.094 3.917,3.292 0.313,0.198 10 false C4 3.604,3.271 5.396,3.729 1.792,0.458 10 false No. 2 Ignition Coil Assembly 3.615,4.677 3.927,4.875 0.313,0.198 10 false C7 3.625,4.885 5.427,5.229 1.802,0.344 10 false No. 3 Ignition Coil Assembly 3.615,6.219 3.927,6.417 0.313,0.198 10 false C9 3.594,6.375 5.5,6.667 1.906,0.292 10 false No. 4 Ignition Coil Assembly 5.896,6.25 6.354,6.448 0.458,0.198 10 false C58 6.281,6.26 6.74,6.458 0.458,0.198 10 false ECM 5.625,5.76 5.938,5.958 0.313,0.198 10 false 71 5.896,5.76 6.51,5.958 0.615,0.198 10 false IGF1 5.646,5.375 5.958,5.573 0.313,0.198 10 false 42 5.906,5.313 6.521,5.51 0.615,0.198 10 false IGT4 5.646,3.854 5.958,4.052 0.313,0.198 10 false 43 5.906,3.792 6.521,3.99 0.615,0.198 10 false IGT3 5.625,2.24 5.938,2.438 0.313,0.198 10 false 44 5.896,2.198 6.51,2.396 0.615,0.198 10 false IGT2 5.604,0.646 5.917,0.844 0.313,0.198 10 false 45 5.875,0.563 6.49,0.76 0.615,0.198 10 false IGT1

A412707E01
0.146,0.083 3.115,0.49 2.969,0.406 12 false w/o Smart Entry and Start System: 5.917,6.25 6.375,6.448 0.458,0.198 10 false C58 6.271,6.26 6.729,6.458 0.458,0.198 10 false ECM 5.615,0.646 5.927,0.844 0.313,0.198 10 false 45 5.896,0.604 6.51,0.802 0.615,0.198 10 false IGT1 5.615,2.26 5.927,2.458 0.313,0.198 10 false 44 5.906,2.167 6.521,2.365 0.615,0.198 10 false IGT2 5.635,3.833 5.948,4.031 0.313,0.198 10 false 43 5.906,3.781 6.521,3.979 0.615,0.198 10 false IGT3 5.656,5.354 5.969,5.552 0.313,0.198 10 false 42 5.885,5.333 6.5,5.531 0.615,0.198 10 false IGT4 5.615,5.76 5.927,5.958 0.313,0.198 10 false 71 5.896,5.76 6.51,5.958 0.615,0.198 10 false IGF1 3.563,6.229 3.875,6.427 0.313,0.198 10 false C9 3.563,6.396 5.469,6.771 1.906,0.375 10 false No. 4 Ignition Coil Assembly 3.583,4.667 3.896,4.865 0.313,0.198 10 false C7 3.573,4.833 5.49,5.219 1.917,0.385 10 false No. 3 Ignition Coil Assembly 3.615,3.083 3.927,3.281 0.313,0.198 10 false C4 3.583,3.271 5.563,3.656 1.979,0.385 10 false No. 2 Ignition Coil Assembly 3.583,1.479 3.896,1.677 0.313,0.198 10 false C1 3.594,1.635 5.563,1.958 1.969,0.323 10 false No. 1 Ignition Coil Assembly 3.719,0.656 3.875,0.854 0.156,0.198 10 false 1 3.76,2.271 3.917,2.469 0.156,0.198 10 false 1 3.76,3.813 3.917,4.01 0.156,0.198 10 false 1 3.75,5.354 3.906,5.552 0.156,0.198 10 false 1 3.76,0.969 3.917,1.167 0.156,0.198 10 false 4 3.76,2.573 3.917,2.771 0.156,0.198 10 false 4 3.75,4.146 3.906,4.344 0.156,0.198 10 false 4 3.74,5.75 3.896,5.948 0.156,0.198 10 false 4 4.958,0.656 5.115,0.854 0.156,0.198 10 false 3 4.958,2.25 5.115,2.448 0.156,0.198 10 false 3 4.969,3.865 5.125,4.063 0.156,0.198 10 false 3 4.948,5.344 5.104,5.542 0.156,0.198 10 false 3 4.969,0.969 5.125,1.167 0.156,0.198 10 false 2 4.99,2.573 5.146,2.771 0.156,0.198 10 false 2 4.969,4.146 5.125,4.344 0.156,0.198 10 false 2 4.979,5.76 5.135,5.958 0.156,0.198 10 false 2 3.948,0.74 4.26,0.938 0.313,0.198 10 false +B 3.948,2.375 4.26,2.573 0.313,0.198 10 false +B 3.938,3.958 4.25,4.156 0.313,0.198 10 false +B 3.938,5.5 4.25,5.698 0.313,0.198 10 false +B 3.969,1.073 4.427,1.271 0.458,0.198 10 false GND 3.958,2.688 4.417,2.885 0.458,0.198 10 false GND 3.969,4.271 4.427,4.469 0.458,0.198 10 false GND 3.948,5.896 4.406,6.094 0.458,0.198 10 false GND 4.635,1.073 5.094,1.271 0.458,0.198 10 false IGF 4.625,2.656 5.083,2.854 0.458,0.198 10 false IGF 4.615,4.281 5.073,4.479 0.458,0.198 10 false IGF 4.604,5.865 5.063,6.063 0.458,0.198 10 false IGF 4.552,0.74 5.167,0.938 0.615,0.198 10 false IGT1 4.563,2.365 5.177,2.563 0.615,0.198 10 false IGT2 4.531,3.938 5.146,4.135 0.615,0.198 10 false IGT3 4.542,5.479 5.156,5.677 0.615,0.198 10 false IGT4 2.563,0.896 3.021,1.094 0.458,0.198 10 false INJ 1.417,1.583 2.406,1.938 0.99,0.354 10 false IG2 NO. 1 0.448,0.896 1.26,1.177 0.813,0.281 10 false IG2-MAIN 1.302,0.677 1.458,0.875 0.156,0.198 10 false 5 2.104,0.646 2.26,0.844 0.156,0.198 10 false 3 2.083,1.167 2.24,1.365 0.156,0.198 10 false 1 1.26,1.167 1.417,1.365 0.156,0.198 10 false 2 2.25,2.969 2.406,3.167 0.156,0.198 10 false 8 1.927,2.969 2.385,3.167 0.458,0.198 10 false IG1 1.25,2.948 1.708,3.146 0.458,0.198 10 false AM1 1.021,2.958 1.177,3.156 0.156,0.198 10 false 7 0.688,3.552 1.219,3.854 0.531,0.302 10 false AM2 0.698,4.125 1.469,4.323 0.771,0.198 10 false J/B-B 0.354,4.802 1.427,5 1.073,0.198 10 false FL MAIN 0.521,5.583 1.594,5.781 1.073,0.198 10 false Battery 1.125,3.375 1.583,3.573 0.458,0.198 10 false K30 1.125,3.563 3.01,3.958 1.885,0.396 10 false Ignition Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTCS (DTC P0351, P0352, P0353 OR P0354)
2.READ OUTPUT DTCS (DTC P0351, P0352, P0353 OR P0354)
a.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

NOTICE:

Do not change the location of the connectors.



b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Perform a simulation test.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

B

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
A412045C01
0.094,0.833 0.385,1.021 0.292,0.188 0.417,0.823 0.677,1.031 0.26,0.208 0.083,1.063 0.396,1.281 0.313,0.219 0.427,1.063 0.677,1.281 0.25,0.219 0.667,1.771 1.156,1.208 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 0.146,0.833 0.458,1.031 0.313,0.198 10 false C1 0.469,0.833 0.781,1.031 0.313,0.198 10 false C4 0.177,1.083 0.49,1.281 0.313,0.198 10 false C7 0.458,1.083 0.771,1.281 0.313,0.198 10 false C9 0.521,1.833 0.833,2.031 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Ignition Coil Assembly)


a.

Disconnect the ignition coil assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C1-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C4-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C7-1 (+B) - Body ground Ignition switch ON 11 to 14 V
C9-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - IGNITION COIL ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-4 (GND) - Body ground Always Below 1 Ω
C4-4 (GND) - Body ground Always Below 1 Ω
C7-4 (GND) - Body ground Always Below 1 Ω
C9-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-2 (IGF) - C58-71 (IGF1) Always Below 1 Ω
C4-2 (IGF) - C58-71 (IGF1) Always Below 1 Ω
C7-2 (IGF) - C58-71 (IGF1) Always Below 1 Ω
C9-2 (IGF) - C58-71 (IGF1) Always Below 1 Ω
C1-3 (IGT1) - C58-45 (IGT1) Always Below 1 Ω
C4-3 (IGT2) - C58-44 (IGT2) Always Below 1 Ω
C7-3 (IGT3) - C58-43 (IGT3) Always Below 1 Ω
C9-3 (IGT4) - C58-42 (IGT4) Always Below 1 Ω
C1-2 (IGF) or C58-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C4-2 (IGF) or C58-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C7-2 (IGF) or C58-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C9-2 (IGF) or C58-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C1-3 (IGT1) or C58-45 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C4-3 (IGT2) or C58-44 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C7-3 (IGT3) or C58-43 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C9-3 (IGT4) or C58-42 (IGT4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR