Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low. The heated oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A254107E23
0.885,3.01 0.583,3.01 false 3.375,1.021 3.104,1.292 false 3.427,1.646 2.885,1.646 false 3.427,1.333 2.823,1.531 false 3.406,2.24 2.885,2.094 false 3.427,2.542 2.771,2.313 false 3.427,2.823 2.875,2.51 false 2.198,2.76 1.688,3.073 false 0.177,2.938 0.604,3.104 0.427,0.167 10 Cover 1.24,3.063 2.125,3.24 0.885,0.177 10 Exhaust Gas 1.792,0.885 2.646,1.083 0.854,0.198 10 Atmosphere 3.396,0.927 3.979,1.135 0.583,0.208 10 Housing 3.448,1.271 4.688,1.438 1.24,0.167 10 Platinum Electrode 3.448,1.573 4.667,1.927 1.219,0.354 10 Solid Electrolyte (Zirconia Element) 3.448,2.469 3.958,2.646 0.51,0.177 10 Heater 3.448,2.75 4.635,2.958 1.188,0.208 10 Coating (Ceramic) 3.448,2.167 4.688,2.333 1.24,0.167 10 Platinum Electrode 4.167,0.979 5.146,1.177 0.979,0.198 10 Output Voltage 4.802,2.927 6.844,3.146 2.042,0.219 10 Richer - Air fuel Ratio - Leaner 5.115,0.792 6.479,1 1.365,0.208 10 Ideal Air fuel Mixture

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.


A413377E01
0.156,0.083 3.615,0.49 3.458,0.406 10 false Reference (System Diagram of Sensor 2): 0.281,0.917 1.229,1.25 0.948,0.333 10 false from Battery 1.208,1.083 1.833,1.448 0.625,0.365 10 false EFI-MAIN NO. 2 1.729,2.135 2.896,2.469 1.167,0.333 10 false EFI-MAIN NO. 2 0.135,1.854 1.083,2.292 0.948,0.438 10 false from EFI-MAIN NO. 1 Relay 3.51,0.802 3.823,1 0.313,0.198 10 false +B 3.958,0.646 4.531,0.958 0.573,0.313 10 false Heater 4.625,0.802 5.24,1 0.615,0.198 10 false HT1B 5.135,0.792 5.75,0.99 0.615,0.198 10 false HT1B 4.594,1.313 5.208,1.51 0.615,0.198 10 false OX1B 5.156,1.323 5.771,1.521 0.615,0.198 10 false OX1B 3.958,1.156 4.875,1.354 0.917,0.198 10 false Sensor 3.5,1.313 3.813,1.51 0.313,0.198 10 false E2 3.469,1.823 5.052,2.135 1.583,0.313 10 false Heated Oxygen Sensor 5.156,2.188 5.771,2.385 0.615,0.198 10 false EX1B 5.844,3.083 6.302,3.281 0.458,0.198 10 false ECM


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) Heated oxygen sensor heater current reaches high limit (1 trip detection logic).
·

Short in heated oxygen sensor (sensor 2) heater circuit

·

Heated oxygen sensor (sensor 2)

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P102D O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in heated oxygen sensor (sensor 2) heater circuit

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated Oxygen Sensor Heater Range Check (P0037, P0038 and P102D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.



MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Time after heater on 5 seconds or more

CONFIRMATION DRIVING PATTERN

A262623E48
0.792,0.969 1.583,1.26 0.792,0.292 10 false 3000 rpm 1.031,1.74 1.552,1.99 0.521,0.25 10 false Idling 0.25,2.01 1.615,2.354 1.365,0.344 10 false Ignition switch ON 1.927,2.135 2.24,2.375 0.313,0.24 10 false [A] 2.76,1.625 3.146,1.938 0.385,0.313 10 false [B] 4.021,0.865 4.323,1.146 0.302,0.281 10 false [C] 5.385,1.604 5.594,2.135 0.208,0.531 10 false [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 false 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 false 5 minutes or more 3.854,2.615 4.458,2.854 0.604,0.24 10 false 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 false [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and idle it for 5 minutes or more [B].

9.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

10.

Idle the engine for 5 minutes or more [D].

11.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

14.

Input the DTC: P0037, P0038 or P102D.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

A412513E01
0.719,5.948 1.479,6.281 0.76,0.333 10 false Battery 0.552,4.979 1.625,5.177 1.073,0.198 10 false FL MAIN 1.531,3.365 2.76,3.698 1.229,0.333 10 false EFI-MAIN NO. 1 0.625,2.948 1.25,3.406 0.625,0.458 10 false EFI-MAIN NO. 1 1.49,2.917 1.646,3.115 0.156,0.198 10 false 1 2.302,2.927 2.458,3.125 0.156,0.198 10 false 2 2.271,2.646 2.427,2.844 0.156,0.198 10 false 5 1.51,2.625 1.667,2.823 0.156,0.198 10 false 3 1.5,1.156 2.646,1.469 1.146,0.313 10 false EFI-MAIN NO. 2 0.542,0.74 1.167,1.094 0.625,0.354 10 false EFI-MAIN NO. 2 1.448,0.448 1.604,0.646 0.156,0.198 10 false 3 1.49,0.74 1.646,0.938 0.156,0.198 10 false 2 2.333,0.448 2.49,0.646 0.156,0.198 10 false 5 2.323,0.729 2.479,0.927 0.156,0.198 10 false 1 3.573,0.438 3.729,0.635 0.156,0.198 10 false 2 3.802,0.427 4.115,0.625 0.313,0.198 10 false +B 4.146,0.438 4.594,0.719 0.448,0.281 10 false HT1B 4.646,0.438 4.802,0.635 0.156,0.198 10 false 1 3.583,1.208 3.74,1.406 0.156,0.198 10 false 4 3.781,1.167 4.094,1.365 0.313,0.198 10 false E2 4.188,1.167 4.719,1.458 0.531,0.292 10 false OX1B 4.656,1.219 4.813,1.417 0.156,0.198 10 false 3 3.385,1.688 3.844,1.885 0.458,0.198 10 false C95 3.708,1.698 5.406,2.031 1.698,0.333 10 false Heated Oxygen Sensor 5.396,0.573 5.854,0.771 0.458,0.198 10 false C58 5.438,0.385 5.75,0.583 0.313,0.198 10 false 55 5.75,0.448 6.365,0.646 0.615,0.198 10 false HT1B 5.406,1.344 5.865,1.542 0.458,0.198 10 false C58 5.417,1.146 5.729,1.344 0.313,0.198 10 false 99 5.781,1.208 6.396,1.406 0.615,0.198 10 false OX1B 5.396,2.021 5.854,2.219 0.458,0.198 10 false C58 5.396,1.854 5.854,2.052 0.458,0.198 10 false 131 5.76,1.927 6.375,2.125 0.615,0.198 10 false EX1B 5.406,3.031 5.865,3.229 0.458,0.198 10 false A22 5.458,2.875 5.771,3.073 0.313,0.198 10 false 46 5.771,3.031 6.385,3.229 0.615,0.198 10 false MREL 6.146,4.813 6.604,5.01 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Refer to "Data List / Active Test" [O2 Heater B1S2 and O2 Heater Curr Val B1S2].

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

When the values for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage (Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)
A412048C01
0.615,0.927 0.99,1.229 0.375,0.302 2.021,0.896 2.5,0.625 true 0.198,0.104 0.51,0.302 0.313,0.198 10 false *a 0.667,0.99 1.125,1.188 0.458,0.198 10 false C95 2.583,0.542 2.896,0.74 0.313,0.198 10 false *B
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


a.

Disconnect the heated oxygen sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C95-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

6.INSPECT EFI-MAIN NO. 2 RELAY
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C95-1 (HT1B) - C58-55 (HT1B) Always Below 1 Ω
C95-1 (HT1B) or C58-55 (HT1B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P102D)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P102D)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTCs are not output A
DTC P0037, P0038 or P102D is output B



A

B

6.INSPECT EFI-MAIN NO. 2 RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)
A404792C01
0.24,0.208 0.552,0.406 0.313,0.198 10 false *1 2.042,0.594 2.354,0.792 0.313,0.198 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 2 Relay


a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - HEATED OXYGEN SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - HEATED OXYGEN SENSOR)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the heated oxygen sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 2 relay) - C95-2 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 2 relay) or C95-2 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR