Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  


DESCRIPTION

The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and is integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), current flows to the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through alumina, and therefore the sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A340232E11
1.75,2.635 2.031,2.427 false 1.583,2.656 1.021,2.208 false 2.906,1.865 3.333,0.656 false 3.063,1.906 3.427,1.323 false 3.177,2.219 3.646,1.76 false 3.063,2.49 3.583,2.802 false 2.823,2.458 3.667,2.156 3.667,2.156 2.99,2.479 false 0.479,2.083 1.135,2.344 0.656,0.26 10 false Element 2.063,2.292 2.531,2.5 0.469,0.208 10 false Cover 0.094,2.99 0.958,3.219 0.865,0.229 10 false Exhaust Gas 1.073,3.156 1.229,3.354 0.156,0.198 10 false A 1.979,3.146 2.135,3.344 0.156,0.198 10 false A 3.375,0.542 4.49,0.979 1.115,0.438 10 false Solid Electrolyte (Zirconia Element) 3.469,1.208 4.135,1.479 0.667,0.271 10 false Alumina 3.698,1.646 4.365,1.917 0.667,0.271 10 false Heater 3.698,2.104 4.365,2.5 0.667,0.396 10 false Platinum Electrode 3.615,2.76 4.688,3.156 1.073,0.396 10 false Atmospheric Air 2.438,3.219 3.646,3.573 1.208,0.354 10 false A-A Cross Section 5.083,0.656 6.938,1.042 1.854,0.385 10 false ECM Monitored Air Fuel Ratio Sensor Voltage 5.583,3.135 6.656,3.531 1.073,0.396 10 false Air Fuel Ratio

HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A413376E01
0.302,0.927 1.469,1.292 1.167,0.365 10 false from Battery 1.198,1.104 1.844,1.479 0.646,0.375 10 false EFI-MAIN NO. 2 0.146,0.073 2.833,0.521 2.688,0.448 10 false Reference (System Diagram of Sensor 1): 0.146,1.833 1.094,2.302 0.948,0.469 10 false from EFI-MAIN NO. 1 Relay 1.719,2.146 2.885,2.552 1.167,0.406 10 false EFI-MAIN NO. 2 3.521,0.802 3.833,1 0.313,0.198 10 false +B 3.396,1.333 4.01,1.531 0.615,0.198 10 false A1A- 3.594,1.823 5.25,2.146 1.656,0.323 10 false Air Fuel Ratio Sensor 3.958,0.646 4.5,0.917 0.542,0.271 10 false Heater 3.938,1.146 4.552,1.469 0.615,0.323 10 false Sensor 4.583,0.781 5.198,0.979 0.615,0.198 10 false HA1A 6.177,1.448 7.021,1.708 0.844,0.26 10 false DutyControl 5.146,1.302 5.76,1.5 0.615,0.198 10 false A1A+ 5.135,0.792 5.75,0.99 0.615,0.198 10 false HA1A 4.604,1.313 5.219,1.51 0.615,0.198 10 false A1A+ 5.146,2.198 5.76,2.396 0.615,0.198 10 false A1A- 5.802,3.083 6.26,3.281 0.458,0.198 10 false ECM



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
·

Open in air fuel ratio sensor (sensor 1) heater circuit

·

Air fuel ratio sensor (sensor 1)

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
·

Short in air fuel ratio sensor (sensor 1) heater circuit

·

Air fuel ratio sensor (sensor 1)

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P101D A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Short in air fuel ratio sensor (sensor 1) heater circuit

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

P0031
Output duty cycle 30% or higher

P0032
Output duty cycle Higher than 0%

P101D
Output duty cycle Less than 60%

CONFIRMATION DRIVING PATTERN

A262623E47
0.792,0.969 1.583,1.26 0.792,0.292 10 false 3000 rpm 1.031,1.74 1.552,1.99 0.521,0.25 10 false Idling 0.281,2.052 1.646,2.396 1.365,0.344 10 false Ignition switch ON 1.927,2.135 2.24,2.375 0.313,0.24 10 false [A] 2.76,1.625 3.146,1.938 0.385,0.313 10 false [B] 4.021,0.865 4.323,1.146 0.302,0.281 10 false [C] 5.385,1.604 5.594,2.135 0.208,0.531 10 false [D] 2.271,2.594 3.469,2.75 1.198,0.156 10 false 5 minutes or more 4.875,2.604 6.073,2.76 1.198,0.156 10 false 5 minutes or more 3.854,2.615 4.458,2.854 0.604,0.24 10 false 1 minute 5.979,3.031 6.177,3.229 0.198,0.198 10 false [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on [A].

8.

Start the engine and idle it for 5 minutes or more [B].

9.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

10.

Idle the engine for 5 minutes or more [D].

11.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

14.

Input the DTC: P0031, P0032 or P101D.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

A412512E01
5.771,0.406 6.385,0.604 0.615,0.198 10 false HA1A 5.396,0.573 5.854,0.771 0.458,0.198 10 false C58 5.448,0.417 5.76,0.615 0.313,0.198 10 false 27 5.771,1.219 6.385,1.417 0.615,0.198 10 false A1A+ 5.417,1.167 5.875,1.365 0.458,0.198 10 false 100 5.396,1.344 5.854,1.542 0.458,0.198 10 false C58 5.063,2.458 5.219,2.656 0.156,0.198 10 false * 5.75,2.031 6.365,2.229 0.615,0.198 10 false A1A- 5.406,2.167 5.865,2.365 0.458,0.198 10 false C58 5.417,1.99 5.875,2.188 0.458,0.198 10 false 132 3.49,1.667 4.104,1.865 0.615,0.198 10 false C102 3.49,1.865 4.885,2.156 1.396,0.292 10 false Air Fuel Ratio Sensor 3.802,1.167 4.417,1.365 0.615,0.198 10 false A1A- 3.552,1.208 3.708,1.406 0.156,0.198 10 false 4 4.188,1.167 4.802,1.365 0.615,0.198 10 false A1A+ 4.656,1.229 4.813,1.427 0.156,0.198 10 false 3 4.146,0.427 4.76,0.625 0.615,0.198 10 false HA1A 4.625,0.438 4.781,0.635 0.156,0.198 10 false 1 3.802,0.427 4.115,0.625 0.313,0.198 10 false +B 3.563,0.417 3.719,0.615 0.156,0.198 10 false 2 5.406,3.031 5.865,3.229 0.458,0.198 10 false A22 5.438,2.844 5.75,3.042 0.313,0.198 10 false 46 5.781,3.031 6.396,3.229 0.615,0.198 10 false MREL 6.24,4.813 6.698,5.01 0.458,0.198 10 false ECM 1.531,1.177 2.688,1.531 1.156,0.354 10 false EFI-MAIN NO. 2 2.292,0.427 2.448,0.625 0.156,0.198 10 false 5 2.281,0.76 2.438,0.958 0.156,0.198 10 false 1 1.5,0.719 1.656,0.917 0.156,0.198 10 false 2 1.5,0.448 1.667,0.667 0.167,0.219 10 false 3 0.625,0.719 1.24,1.219 0.615,0.5 10 false EFI-MAIN NO. 2 1.531,3.365 2.833,3.76 1.302,0.396 10 false EFI-MAIN NO. 1 0.667,2.917 1.292,3.469 0.625,0.552 10 false EFI-MAIN NO. 1 2.26,2.646 2.417,2.844 0.156,0.198 10 false 5 1.49,2.646 1.646,2.844 0.156,0.198 10 false 3 1.51,2.917 1.667,3.115 0.156,0.198 10 false 1 2.292,2.917 2.448,3.115 0.156,0.198 10 false 2 0.573,4.958 1.448,5.25 0.875,0.292 10 false FL MAIN 4.188,4.042 5.313,4.375 1.125,0.333 10 false *: Shielded 0.698,5.958 1.771,6.156 1.073,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F Heater Duty B1S1].

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage (Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
A240487C09
0.521,0.958 1.042,1.271 0.521,0.313 1.948,0.854 2.365,0.438 true 0.594,1.021 1.208,1.219 0.615,0.198 10 false C102 0.146,0.073 0.458,0.271 0.313,0.198 10 false *a 2.396,0.333 2.708,0.531 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


a.

Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C102-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

6.INSPECT EFI-MAIN NO. 2 RELAY
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C102-1 (HA1A) - C58-27 (HA1A) Always Below 1 Ω
C102-1 (HA1A) or C58-27 (HA1A) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


c.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTCs are not output A
DTC P0031, P0032 or P101D is output B



A

B

6.INSPECT EFI-MAIN NO. 2 RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 2 RELAY)
A404792C01
0.24,0.208 0.552,0.406 0.313,0.198 10 false *1 2.042,0.594 2.354,0.792 0.313,0.198 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 EFI-MAIN NO. 2 Relay


a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - AIR FUEL RATIO SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - AIR FUEL RATIO SENSOR)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the air fuel ratio sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 2 relay) - C102-2 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 2 relay) or C102-2 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR