Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0329835 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P034031  Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal  P034531  Camshaft Position Sensor "A" Bank 2 No Signal  


DESCRIPTION

Refer to DTC P034011.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>P034011

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal A missing VVT sensor (for intake camshaft of bank 1) signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

Intake camshaft

·

Valve timing

·

ECM


Comes on DTC stored SAE Code: P0340
P034531 Camshaft Position Sensor "A" Bank 2 No Signal A missing VVT sensor (for intake camshaft of bank 2) signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

Intake camshaft

·

Valve timing

·

ECM


Comes on DTC stored SAE Code: P0345

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>P034011

MONITOR DESCRIPTION

If no pulse signal is transmitted by the VVT sensor (for intake camshaft) despite the camshaft rotating the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) VVT sensor (for intake camshaft)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Start the engine [A].

7.

Idle the engine for 10 seconds or more [B].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P034031 or P034531.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A376492C69
0.198,1.156 0.552,1.406 0.354,0.25 0.198,0.813 0.552,1.063 0.354,0.25 1.958,1.167 2.448,1.76 true 1.385,1.167 0.844,1.677 true 1.625,1.167 1.594,1.844 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.26,1.198 0.573,1.396 0.313,0.198 10 false C19 2.396,1.771 2.708,1.969 0.313,0.198 10 false VC 0.25,0.854 0.563,1.052 0.313,0.198 10 false C16 0.583,0.823 0.896,1.021 0.313,0.198 10 false *b 0.583,1.167 0.896,1.365 0.313,0.198 10 false *c 0.563,1.688 1.125,1.917 0.563,0.229 10 false VVR+*b 0.563,1.833 1.125,2.063 0.563,0.229 10 false VVL+*c 1.344,1.854 1.906,2.083 0.563,0.229 10 false VVR-*b 1.344,2 1.927,2.177 0.583,0.177 10 false VVL-*c
*a Front view of wire harness connector
(to VVT Sensor (for Intake Camshaft))
*b Bank 1
*c Bank 2


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C16-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
C19-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
C16-1 (VVR+) - Body ground Engine switch on (IG) 3.0 to 5.0 V
C19-1 (VVL+) - Body ground Engine switch on (IG) 3.0 to 5.0 V



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-3 (VC) - C16-1 (VVR+) Engine switch off 1.425 to 1.575 kΩ
C19-3 (VC) - C19-1 (VVL+) Engine switch off 1.425 to 1.575 kΩ
C16-2 (VVR-) - Body ground Always Below 1 Ω
C19-2 (VVL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (VVT SENSOR (FOR INTAKE CAMSHAFT))

NG

4.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK SENSOR INSTALLATION AND CONDUCT VISUAL INSPECTION (VVT SENSOR (FOR INTAKE CAMSHAFT))
A316078C01
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


a.

Visually check the VVT sensor (for intake camshaft) for damage.


b.

Check the VVT sensor (for intake camshaft) installation condition.

OK:

The VVT sensor (for intake camshaft) does not have any damage and is installed properly.



Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL VVT SENSOR (FOR INTAKE CAMSHAFT)

3.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the intake camshaft.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-1 (VVR+) - C96-132 (VV1+) Always Below 1 Ω
C16-2 (VVR-) - C96-100 (VV1-) Always Below 1 Ω
C16-3 (VC) - C96-99 (VCV1) Always Below 1 Ω
C19-1 (VVL+) - C96-129 (VV2+) Always Below 1 Ω
C19-2 (VVL-) - C96-97 (VV2-) Always Below 1 Ω
C19-3 (VC) - C96-98 (VCV2) Always Below 1 Ω
C16-1 (VVR+) or C96-132 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
C16-2 (VVR-) or C96-100 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
C16-3 (VC) or C96-99 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
C19-1 (VVL+) or C96-129 (VV2+) - Body ground and other terminals Always 10 kΩ or higher
C19-2 (VVL-) or C96-97 (VV2-) - Body ground and other terminals Always 10 kΩ or higher
C19-3 (VC) or C96-98 (VCV2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR