1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT
Remove the front door scuff plate LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Remove the cowl side trim sub-assembly LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
Remove the No. 1 instrument panel under cover sub-assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
Remove the accelerator pedal pad.
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
Remove the accelerator pedal.
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
Check the brake pedal height.
Inspect and adjust the brake pedal height with the floor carpet and front floor mat folded back.
Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.
| *1 | Brake Pedal Pad | - | - |
| *a | Brake Pedal Height | *b | Measuring Plane of Floor Panel |
| *c | 36 mm (1.42 in.) | - | - |
149.5 to 159.5 mm (5.89 to 6.28 in.)
If the brake pedal height is not as specified, inspect and adjust the push rod length according to the procedure below.
Adjust the push rod length.
| *1 | Lock Nut |
| *2 | Stop Light Switch Assembly |
| *a | Floor Panel |
| *b | Brake Pedal Height |
Remove the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Loosen the lock nut.
Adjust the brake pedal height by turning the push rod.
149.5 to 159.5 mm (5.89 to 6.28 in.)
Tighten the lock nut.
Install the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
Install the accelerator pedal.
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>INSTALLATION
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ACCELERATOR PEDAL>INSTALLATION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ACCELERATOR PEDAL>INSTALLATION
Install the accelerator pedal pad.
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>ACCELERATOR PEDAL>INSTALLATION
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ACCELERATOR PEDAL>INSTALLATION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ACCELERATOR PEDAL>INSTALLATION
Install the No. 1 instrument panel under cover sub-assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION
Install the cowl side trim sub-assembly LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
Install the front door scuff plate LH.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
2.INSPECT BRAKE PEDAL FREE PLAY
Stop the engine and firmly depress the brake pedal several times until no vacuum is left in the brake booster assembly.
| *a | Brake Pedal Free Play |
Depress the brake pedal until a slight resistance is felt. Measure the distance as shown in the illustration.
1.0 to 6.0 mm (0.0394 to 0.236 in.)
If the brake pedal free play is not as specified, check the stop light switch clearance.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
If the brake pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.
3.INSPECT BRAKE PEDAL RESERVE DISTANCE
Measure the distance at the same point used for the brake pedal height inspection.
With the engine running, depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.
| *1 | Brake Pedal Pad | - | - |
| *a | Brake Pedal Reserve Distance | *b | Measuring Plane of Floor Panel |
| *c | 36 mm (1.42 in.) | - | - |
| Front Brake | Engine | Specification |
|---|---|---|
| for 16 inch Front Disc Brake | for 2AR-FE | 86 mm (3.39 in.) or more |
| for A25A-FKS, 2GR-FKS | 81 mm (3.19 in.) or more | |
| for 17 inch Front Disc Brake | - | 79 mm (3.11 in.) or more |
If the distance is not as specified, troubleshoot the brake system.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE