This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B150013 | Fuel Sender Circuit Open | Diagnosis Condition:
·
The ignition switch is ON ·
IG power source voltage is 9.5 V or more Malfunction Status: ·
Voltage signal from fuel sender gauge assembly is 0.2 V or less 3.0 times consecutively ·
Voltage signal from fuel sender gauge assembly is 4.7 V or more 3.0 times consecutively |
·
Harness or connector ·
Fuel sender gauge assembly ·
Fuel suction tube with pump and gauge assembly ·
Combination meter assembly |
DTC stored | - |
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fuel Input | Fuel input | Min.: 0 L, Max.: 655.35 L or Unset | ·
Fuel receiver gauge indicates F: 54.5 L ·
Fuel receiver gauge indicates 3/4: 45.5 L ·
Fuel receiver gauge indicates 1/2: 30.3 L ·
Fuel receiver gauge indicates 1/4: 15.2 L ·
Fuel receiver gauge indicates E: 6.1 L |
- |
| Tester Display |
|---|
| Fuel Input |
| Result | Proceed to |
|---|---|
| Fuel level data can be displayed on the GTS | A |
| Fuel level data cannot be displayed on the GTS | B |
A
B
Disconnect the R44 fuel suction tube with pump and gauge assembly connector.
Disconnect the K21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R44-1 (FV) - K21-15 (FV) | Always | Below 1 Ω |
| R44-3 (FS) - K21-14 (FR) | Always | Below 1 Ω |
| R44-2 (FE) - K21-33 (FE) | Always | Below 1 Ω |
| R44-1 (FV) or K21-15 (FV) - Body ground | Always | 10 kΩ or higher |
| R44-3 (FS) or K21-14 (FR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel sender gauge assembly.
for A25A-FKS (w/ Canister Pump Module): Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY(w/ Canister Pump Module)>REMOVAL
for A25A-FKS (w/o Canister Pump Module): Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Inspect the fuel sender gauge assembly.
for A25A-FKS (w/ Canister Pump Module): Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY(w/ Canister Pump Module)>INSPECTION
for A25A-FKS (w/o Canister Pump Module): Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>INSPECTION
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for A25A-FKS (w/ Canister Pump Module): Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY(w/ Canister Pump Module)>REMOVAL
for A25A-FKS (w/o Canister Pump Module): Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module)>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
| *a | Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R44-1 (FV) - A-3 | Always | Below 1 Ω |
| R44-2 (FE) - A-2 | Always | Below 1 Ω |
| R44-3 (FS) - A-1 | Always | Below 1 Ω |
| R44-1 (FV) - R44-3 (FS)
or A-3 - A-1 |
Always | 10 kΩ or higher |
| R44-1 (FV) - R44-2 (FE)
or A-3 - A-2 |
Always | 10 kΩ or higher |
| R44-2 (FE) - R44-3 (FS)
or A-2 - A-1 |
Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for A25A-FKS (w/ Canister Pump Module): Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL PUMP (w/ Canister Pump Module)>REMOVAL
for A25A-FKS (w/o Canister Pump Module): Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL PUMP (w/o Canister Pump Module)>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL PUMP>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL PUMP>REMOVAL