Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.12–2018.04
RM33A0E _58 Vehicle Interior _065381 METER / GAUGE / DISPLAY _0323396 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

FUEL RECEIVER GAUGE OPERATION


a.

OPERATION

The combination meter assembly uses the fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. The Hall IC built into the fuel sender gauge assembly changes the output voltage according to the amount of fuel remaining. The combination meter assembly receives fuel injection volume signals from the ECM and detects the voltage output from the fuel sender gauge assembly and operates the fuel receiver gauge.



FUEL RECEIVER GAUGE READING


a.

During normal driving:

As the fuel level in the fuel tank assembly changes when driving on a hill or applying the brakes, the fuel receiver gauge reading is updated according to the fuel injection volume during normal driving. However, as the fuel injection volume measurement has a margin of error, the value is indicated after correction by input values from the fuel sender gauge assembly.


b.

During refueling:

The fuel level in the fuel tank assembly rises rapidly when fuel is added. If the averaging process that is used during normal driving is used in this case, the fuel receiver gauge reading cannot be updated promptly. Therefore, when it is judged that fuel is being added to the vehicle based on the changes in the fuel level, output values from the fuel sender gauge assembly is immediately reflected in the fuel receiver gauge reading. This control is called refueling judgment.



REFUELING JUDGMENT CONDITIONS


NOTICE:

Add fuel with the ignition switch off to ensure safety and to enable refueling judgment so that an appropriate fuel receiver gauge reading will be obtained.


a.

Normal judgment condition (When normal refueling method is used)

With the ignition switch off, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.


b.

Other judgment conditions (When other refueling method is used)

Any of the following conditions is met:

·

With the vehicle and engine stopped and the ignition switch ON, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.

·

With the vehicle stopped, the ignition switch is ON, the fuel sender gauge assembly detects a change of 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more in the fuel level.




PRECAUTION FOR REFUELING


a.

The fuel sender gauge assembly cannot detect changes in the fuel level within certain ranges (around points E and F). Therefore, even if 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more of fuel is added, refueling judgment may not be performed and the fuel receiver gauge reading may not change when fuel level is within such ranges.


b.

The fuel sender gauge reading takes approximately 25 seconds to rise from point E to F. If the vehicle is driven while the fuel sender gauge reading is rising, the fuel sender gauge reading will stop rising. After the fuel sender gauge reading stops rising, normal fuel sender gauge reading operation begins. The fuel sender gauge reading takes approximately 1 minute per 1 liter (1.1 US qts, 0.9 Imp. qts) to rise while the vehicle is being driven, and takes approximately 7 minutes per 1 liter (1.1 US qts, 0.9 Imp. qts) to rise while the vehicle is stopped.



FORCED RESET OF FUEL RECEIVER GAUGE


When driving at a vehicle speed of 1.8 km/h (1 mph) or more, if the output value from the fuel sender gauge assembly is different from the fuel receiver gauge reading by 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more for approximately 5 minutes, the output value from the fuel sender gauge assembly is immediately reflected in the fuel receiver gauge reading to compensate for a situation when refueling judgment cannot be made.


WIRING DIAGRAM

E367210E01
2.552,1.417 2.708,1.615 0.156,0.198 10 false 3 2.531,2.083 2.688,2.281 0.156,0.198 10 false 2 2.521,0.729 2.677,0.927 0.156,0.198 10 false 1 2.198,0.719 2.448,0.906 0.25,0.188 10 false FV 2.24,1.406 2.458,1.583 0.219,0.177 10 false FS 2.24,2.083 2.458,2.26 0.219,0.177 10 false FE 1.875,1.167 2.031,1.365 0.156,0.198 10 false 3 1.885,1.875 2.042,2.073 0.156,0.198 10 false 2 2.021,1.406 2.177,1.604 0.156,0.198 10 false 1 5.573,0.719 5.76,0.927 0.188,0.208 10 false 15 5.604,2.083 5.781,2.302 0.177,0.219 10 false 33 5.594,1.427 5.802,1.615 0.208,0.188 10 false 14 0.302,2.833 0.573,3.021 0.271,0.188 10 false R44 0.313,3.01 3.5,3.219 3.188,0.208 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.719,1.375 1.479,1.917 0.76,0.542 10 false Fuel Sender Gauge Assembly 5.854,0.719 6.104,0.906 0.25,0.188 10 false FV 5.854,2.083 6.073,2.26 0.219,0.177 10 false FE 5.854,1.427 6.146,1.625 0.292,0.198 10 false FR 0.729,1.188 0.885,1.385 0.156,0.198 10 false A 5.198,3.177 7.094,3.375 1.896,0.198 10 false Combination Meter Assembly 5.219,2.969 5.5,3.177 0.281,0.208 10 false K21 6.385,1.521 6.604,1.698 0.219,0.177 10 false I/F 6.406,0.396 6.656,0.583 0.25,0.188 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:

The fuel level warning light will come on when the fuel level is below 9.1 liters (9.6 US qts, 8.0 Imp. qts).


PROCEDURE

1.CHECK SYMPTOMS
a.

Ask the customer about the problem symptoms.


Result:
Result Proceed to
Malfunction occurs when adding fuel (Even after adding fuel, reading does not increase at all or increases very slowly, etc.) A
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom recurs) B
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom does not recur) C



A

2.PERFORM ACTIVE TEST USING GTS

B

7.PERFORM ACTIVE TEST USING GTS

C

12.CHECK FOR DTC (SFI SYSTEM)
2.PERFORM ACTIVE TEST USING GTS
E365752C02
3.125,0.396 1.365,0.531 false 2.865,0.542 1.365,0.531 false 2.417,1.24 1.365,0.531 false 1.167,1.813 1.365,0.521 false 1.833,1.625 1.365,0.521 false 0.75,1.677 1.365,0.521 false 0.333,1.792 1.365,0.542 false 0.406,1.438 1.375,0.531 false 0.24,1.427 0.427,1.604 0.188,0.177 10 false *a 0.208,1.813 0.417,1.99 0.208,0.177 10 false *b 1.063,1.833 1.24,1.99 0.177,0.156 10 false *d 1.802,1.688 1.979,1.844 0.177,0.156 10 false *e 2.458,1.26 2.688,1.438 0.229,0.177 10 false *f 2.927,0.469 3.188,0.635 0.26,0.167 10 false *g 3.219,0.313 3.396,0.469 0.177,0.156 10 false *h 0.625,1.708 0.802,1.865 0.177,0.156 10 false *c
*a Fuel Gauge Operation (Sender E)
*b Fuel Gauge Operation (Empty)
*c Fuel Gauge Operation (Warning)
*d Fuel Gauge Operation (1/4)
*e Fuel Gauge Operation (1/2)
*f Fuel Gauge Operation (3/4)
*g Fuel Gauge Operation (Full)
*h Fuel Gauge Operation (Sender F)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Gauge Operation (Sender E) Fuel receiver gauge (Sender E) ON -
Fuel Gauge Operation (Empty) Fuel receiver gauge (Empty) ON -
Fuel Gauge Operation (Warning) Fuel receiver gauge (Warning) ON -
Fuel Gauge Operation (1/4) Fuel receiver gauge (1/4) ON -
Fuel Gauge Operation (1/2) Fuel receiver gauge (1/2) ON -
Fuel Gauge Operation (3/4) Fuel receiver gauge (3/4) ON -
Fuel Gauge Operation (Full) Fuel receiver gauge (Full) ON -
Fuel Gauge Operation (Sender F) Fuel receiver gauge (Sender F) ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Sender E)
50004 409 221
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Empty)
50004 409 222
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Warning)
50004 409 223
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (1/4)
50004 409 224
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (1/2)
50004 409 225
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (3/4)
50004 409 226
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Full)
50004 409 227
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Sender F)
50004 409 228
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC (SFI SYSTEM)

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK FOR DTC (SFI SYSTEM)
a.

Check if SFI system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

4.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

4.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check if vehicle stability control system DTCs are output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL

B

5.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL
a.

Record the fuel receiver gauge reading.


b.

If the fuel tank assembly is almost full, drain 20 liters (21.1 US qts, 17.6 Imp. qts) or more of fuel. (This is not necessary when the fuel tank assembly is sufficiently below full.)


c.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



d.

Connect the cable to the negative (-) battery terminal and turn the ignition switch to ON.


e.

Check that the fuel receiver gauge has been reset.


f.

Drive the vehicle at 1.8 km/h (1 mph) or more, then move the shift lever to P and turn the ignition switch off.


g.

Add 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more of fuel, turn the ignition switch to ON, and check that the fuel receiver gauge reading increases in proportion to the amount of fuel added.


Result:
Result Proceed to
Fuel receiver gauge reading increases in proportion to the amount of fuel added A
Fuel receiver gauge reading does not change even when fuel is added B



A

6.INSPECT FUEL TANK ASSEMBLY

B

REPLACE COMBINATION METER ASSEMBLY

6.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal B
There is an excessive amount of foreign matter in the fuel tank assembly C
The fuel tank assembly or fuel sender gauge assembly is not installed correctly D



A

REPLACE COMBINATION METER ASSEMBLY

B

C

CLEAN INSIDE OF FUEL TANK ASSEMBLY

D

INSTALL FUEL TANK ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY

7.PERFORM ACTIVE TEST USING GTS
E365752C02
3.125,0.396 1.365,0.531 false 2.865,0.542 1.365,0.531 false 2.417,1.24 1.365,0.531 false 1.167,1.813 1.365,0.521 false 1.833,1.625 1.365,0.521 false 0.75,1.677 1.365,0.521 false 0.333,1.792 1.365,0.542 false 0.406,1.438 1.375,0.531 false 0.24,1.427 0.427,1.604 0.188,0.177 10 false *a 0.208,1.813 0.417,1.99 0.208,0.177 10 false *b 1.063,1.833 1.24,1.99 0.177,0.156 10 false *d 1.802,1.688 1.979,1.844 0.177,0.156 10 false *e 2.458,1.26 2.688,1.438 0.229,0.177 10 false *f 2.927,0.469 3.188,0.635 0.26,0.167 10 false *g 3.219,0.313 3.396,0.469 0.177,0.156 10 false *h 0.625,1.708 0.802,1.865 0.177,0.156 10 false *c
*a Fuel Gauge Operation (Sender E)
*b Fuel Gauge Operation (Empty)
*c Fuel Gauge Operation (Warning)
*d Fuel Gauge Operation (1/4)
*e Fuel Gauge Operation (1/4)
*f Fuel Gauge Operation (3/4)
*g Fuel Gauge Operation (Full)
*h Fuel Gauge Operation (Sender F)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Gauge Operation (Sender E) Fuel receiver gauge (Sender E) ON -
Fuel Gauge Operation (Empty) Fuel receiver gauge (Empty) ON -
Fuel Gauge Operation (Warning) Fuel receiver gauge (Warning) ON -
Fuel Gauge Operation (1/4) Fuel receiver gauge (1/4) ON -
Fuel Gauge Operation (1/2) Fuel receiver gauge (1/2) ON -
Fuel Gauge Operation (3/4) Fuel receiver gauge (3/4) ON -
Fuel Gauge Operation (Full) Fuel receiver gauge (Full) ON -
Fuel Gauge Operation (Sender F) Fuel receiver gauge (Sender F) ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Sender E)
50004 409 221
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Empty)
50004 409 222
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Warning)
50004 409 223
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (1/4)
50004 409 224
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (1/2)
50004 409 225
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (3/4)
50004 409 226
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Full)
50004 409 227
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Gauge Operation (Sender F)
50004 409 228
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

8.CHECK FOR DTC (SFI SYSTEM)

NG

REPLACE COMBINATION METER ASSEMBLY

8.CHECK FOR DTC (SFI SYSTEM)
a.

Check if SFI system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

9.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

9.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check if vehicle stability control system DTCs are output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

10.CHECK FOR DTC (METER / GAUGE SYSTEM)

B

10.CHECK FOR DTC (METER / GAUGE SYSTEM)
a.

Check if meter / gauge system DTCs are output.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTC B150013 is not output A
DTC B150013 is output B



A

11.INSPECT FUEL RECEIVER GAUGE

B

11.INSPECT FUEL RECEIVER GAUGE
a.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



b.

Connect the cable to the negative (-) battery terminal and turn the ignition switch to ON.


c.

Check if the fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly.


Result:
Result Proceed to
Fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly A
Fuel receiver gauge reading does not correspond with the amount of fuel remaining in the fuel tank assembly B



A

END

B

REPLACE COMBINATION METER ASSEMBLY

12.CHECK FOR DTC (SFI SYSTEM)
a.

Check if SFI system DTCs are output.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

13.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

13.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check if vehicle stability control system DTCs are output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

14.INSPECT FUEL TANK ASSEMBLY

B

14.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly and fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal B
There is an excessive amount of foreign matter in the fuel tank assembly C
The fuel tank assembly or fuel sender gauge assembly is not installed correctly D



A

REPLACE COMBINATION METER ASSEMBLY

B

C

CLEAN INSIDE OF FUEL TANK ASSEMBLY

D

INSTALL FUEL TANK ASSEMBLY OR FUEL SENDER GAUGE ASSEMBLY CORRECTLY