Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for 2AR-FE) › 2017.12–2021.02
RM33A0E _51 Engine / Hybrid System _065357 CRUISE CONTROL _0327281 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2AR-FE) J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2AR-FE)  Steering Pad Switch Circuit  


DESCRIPTION

·

The steering pad switch assembly outputs the on/off signal and various control signals to the ECM.

·

The ECM performs cruise control according to the signals received from the steering pad switch assembly.


WIRING DIAGRAM

A412001E04
0.458,1.49 1.073,1.688 0.615,0.198 10 false -SET 1.25,1.49 1.865,1.688 0.615,0.198 10 false +RES 1.823,1.49 2.438,1.688 0.615,0.198 10 false CANCEL 2.5,1.5 3.115,1.698 0.615,0.198 10 false MAIN 2.75,0.75 3.365,0.948 0.615,0.198 10 false CCS 2.76,1.948 3.375,2.146 0.615,0.198 10 false ECC 0.74,2.552 2.813,2.802 2.073,0.25 10 false Steering Pad Switch Assembly 0.74,2.729 2.813,2.979 2.073,0.25 10 false (Cruise Control Switch) 3.188,2.573 5.26,2.823 2.073,0.25 10 false Spiral Cable Sub-assembly 3.24,2.073 3.854,2.271 0.615,0.198 10 false z1 3.229,0.865 3.844,1.063 0.615,0.198 10 false z1 3.26,0.656 3.875,0.854 0.615,0.198 10 false 2 3.219,1.844 3.833,2.042 0.615,0.198 10 false 12 4.333,0.885 4.948,1.083 0.615,0.198 10 false K22 4.323,2.094 4.938,2.292 0.615,0.198 10 false K22 4.385,0.667 5,0.865 0.615,0.198 10 false 13 4.406,1.854 5.021,2.052 0.615,0.198 10 false 2 5.708,0.885 6.323,1.083 0.615,0.198 10 false A22 5.719,2.073 6.333,2.271 0.615,0.198 10 false A22 5.708,2.854 6.323,3.052 0.615,0.198 10 false C58 3.74,0.76 4.354,0.958 0.615,0.198 10 false CCS 3.75,1.958 4.365,2.156 0.615,0.198 10 false ECC 6.104,0.885 6.719,1.083 0.615,0.198 10 false CCS 6.115,2.073 6.729,2.271 0.615,0.198 10 false ECCS 6.104,2.833 6.719,3.031 0.615,0.198 10 false E1 6.417,3.427 7.031,3.625 0.615,0.198 10 false ECM 5.75,0.667 6.052,0.927 0.302,0.26 10 false 36 5.76,1.854 6.063,2.115 0.302,0.26 10 false 35 5.76,2.635 6.063,2.896 0.302,0.26 10 false 59

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Before replacing the ECM, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.
A401987C01
0.208,0.177 0.521,0.333 0.313,0.156 10 false *1 3.021,1.271 3.333,1.427 0.313,0.156 10 false *a 1.208,1.813 1.396,1.969 0.188,0.156 10 true *b 2.729,0.635 3.042,0.792 0.313,0.156 10 false *c 1.219,1.479 1.531,1.635 0.313,0.156 10 false *d
*1 Steering Pad Switch Assembly
*a Cruise Control Main Switch
*b -SET Switch
*c +RES Switch
*d CANCEL Switch


Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise 1 / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch pushed
OFF: CANCEL switch not pushed
-
-SET Switch -SET switch status ON or OFF ON: -SET switch pushed
OFF: -SET switch not pushed
-
+RES Switch +RES switch status ON or OFF ON: +RES switch pushed
OFF: +RES switch not pushed
-
Cruise Main Switch Operation Condition Cruise control main switch status ON or OFF ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed
-
Powertrain > Radar Cruise1 > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 239 117,116,115,91
OK:

The value of each measurement item changes according to the operation of the steering pad switch assembly.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the K22 spiral cable sub-assembly connector.


b.

Disconnect the A22 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-36 (CCS) - K22-13 (CCS) Always Below 1 Ω
A22-35 (ECCS) - K22-2 (ECC) Always Below 1 Ω
A22-36 (CCS) or K22-13 (CCS) - Body ground Always 10 kΩ or higher
A22-35 (ECCS) or K22-2 (ECC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the C58 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-59 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR