Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Smart Entry and Start System) › 2017.12–2021.02
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328238 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

·

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set (no key is in the ignition key cylinder).

·

The main body ECU (multiplex network body ECU) blinks the security indicator light when the theft deterrent system is in the arming preparation state or alarm sounding state.


WIRING DIAGRAM

B460716E07
0.438,1.188 1.052,1.385 0.615,0.198 10 false 6*1 7*2 2.438,1.188 2.719,1.385 0.281,0.198 10 false LP 1.125,1.198 1.406,1.396 0.281,0.198 10 false E 5.458,1.198 5.781,1.458 0.323,0.26 10 false IND 5.448,3.729 5.771,3.99 0.323,0.26 10 false IND 5.344,2.177 5.667,2.438 0.323,0.26 10 false K60 5.365,4.688 5.688,4.948 0.323,0.26 10 false K52 0.865,2.177 1.188,2.438 0.323,0.26 10 false K36 0.865,2.333 2.833,2.854 1.969,0.521 10 false Security Indicator Light (Telltale Light Assembly) *1 5.354,2.344 6.802,2.802 1.448,0.458 10 false Transponder Key ECU Assembly 5.365,4.854 7.021,5.313 1.656,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 2.76,1.167 3.427,1.365 0.667,0.198 10 false 9*1 5*2 5.219,1.177 5.375,1.375 0.156,0.198 10 false 8 5.24,3.729 5.5,4.052 0.26,0.323 10 false 7 0.823,3.177 2.792,3.698 1.969,0.521 10 false Security Indicator Light (Clock Assembly) *2 0.854,2.99 1.177,3.25 0.323,0.26 10 false K59 0.24,4.583 2.208,5.104 1.969,0.521 10 false *1: w/ Radio Receiver 0.25,4.969 2.219,5.49 1.969,0.521 10 false *2: w/o Radio Receiver

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to Service Bulletin.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Security Indicator
50004 123 19

Result:
Result Proceed to
Security indicator light operation is normal when performing the "Main Body" and "Immobiliser" Active Test A
·

Security indicator light operation is not normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is normal when performing the "Main Body" Active Test


B
·

Security indicator light operation is normal when performing the "Immobiliser" Active Test

·

Security indicator light operation is not normal when performing the "Main Body" Active Test


C
Security indicator light operation is not normal when performing the "Main Body" and "Immobiliser" Active Test D



A

2.CHECK SECURITY INDICATOR LIGHT OPERATION

B

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

D

5.INSPECT SECURITY INDICATOR LIGHT
2.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light is on.*2

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

OK:

The security indicator light is on.



Result:
Result Proceed to
Both *1 and *2 are OK A
*1 is NG (*2 is OK) B
*2 is NG (*1 is OK) C
Both *1 and *2 are NG (w/ Radio Receiver) D
Both *1 and *2 are NG (w/o Radio Receiver) E



A

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

D

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

E

REPLACE SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the K36*1 or K59*2 security indicator light connector.

*1: w/ Radio Receiver

*2: w/o Radio Receiver



b.

Disconnect the K60 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Radio Receiver
Tester Connection Condition Specified Condition
K60-8 (IND) - K36-9 (LP) Always Below 1 Ω
K60-8 (IND) or K36-9 (LP) - Other terminals and body ground Always 10 kΩ or higher


Standard Resistance:
w/o Radio Receiver
Tester Connection Condition Specified Condition
K60-8 (IND) - K59-5 (LP) Always Below 1 Ω
K60-8 (IND) or K59-5 (LP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K36*1 or K59*2 security indicator light connector.

*1: w/ Radio Receiver

*2: w/o Radio Receiver



b.

Disconnect the K52 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Radio Receiver
Tester Connection Condition Specified Condition
K52-7 (IND) - K36-9 (LP) Always Below 1 Ω
K52-7 (IND) or K36-9 (LP) - Other terminals and body ground Always 10 kΩ or higher


Standard Resistance:
w/o Radio Receiver
Tester Connection Condition Specified Condition
K52-7 (IND) - K59-5 (LP) Always Below 1 Ω
K52-7 (IND) or K59-5 (LP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SECURITY INDICATOR LIGHT


Result:
Result Proceed to
OK A
NG (w/ Radio Receiver) B
NG (w/o Radio Receiver) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE SECURITY INDICATOR LIGHT (TELLTALE LIGHT ASSEMBLY)

C

REPLACE SECURITY INDICATOR LIGHT (CLOCK ASSEMBLY)