Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.12–2018.04
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328237 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2799  Engine Immobiliser System Malfunction  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

If there is a communication malfunction between the ECM and certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, or when the communication ID codes do not match, the ECM stores this DTC.

*1: w/o ID Code Box

*2: w/ ID Code Box


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either of the following conditions is met (1 trip detection logic*1):
·

A malfunction is detected in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly)*2 or ID code box (immobiliser code ECU)*3.

·

The communication ID codes of the ECM and certification ECU (smart key ECU assembly)*2 or ID code box (immobiliser code ECU)*3 do not match.


·

Certification ECU (smart key ECU assembly)*2

·

ID code box (immobiliser code ECU)*3

·

ECM

·

Wire harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the engine and wait for 10 seconds. If there is a malfunction, the engine will stop (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) battery terminal, start the engine and wait for 10 seconds (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).


B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either of the following conditions is met (1 trip detection logic*1):
·

A malfunction is detected in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly)*2 or ID code box (immobiliser code ECU)*3.

·

The communication ID codes of the ECM and certification ECU (smart key ECU assembly)*2 or ID code box (immobiliser code ECU)*3 do not match.


·

Certification ECU (smart key ECU assembly)*2

·

ID code box (immobiliser code ECU)*3

·

ECM

·

Wire harness or connector


DTC output confirmation operation (Perform either of the following):
·

Start the engine and wait for 10 seconds. If there is a malfunction, the engine will stop (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

Connect the cable to the negative (-) battery terminal, start the engine and wait for 10 seconds (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: w/o ID Code Box

*3: w/ ID Code Box


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2799*1
B279986*2
-

*1: for 2AR-FE

*2: except 2AR-FE


WIRING DIAGRAM

w/o ID Code Box


B463090E08
0.458,3.063 0.917,3.26 0.458,0.198 10 false ECM 0.448,2.896 1.906,3.198 1.458,0.302 10 false A24*1, A23*2, A22*3 5.313,2.896 5.771,3.094 0.458,0.198 10 false A13 5.979,0.24 6.438,0.438 0.458,0.198 10 false 12 V 1.125,1.375 1.583,1.573 0.458,0.198 10 false 12 V 5.292,0.969 5.75,1.167 0.458,0.198 10 false EFII 5.302,1.865 5.76,2.063 0.458,0.198 10 false EFIO 5.104,0.969 5.563,1.167 0.458,0.198 10 false 3 5.104,1.865 5.563,2.063 0.458,0.198 10 false 4 1.625,0.948 2.208,1.167 0.583,0.219 10 false IMO 1.688,1.865 2.146,2.063 0.458,0.198 10 false IMI 1.969,0.948 2.958,1.26 0.99,0.313 10 false 25*1, 45*2*3 1.969,1.865 3.292,2.125 1.323,0.26 10 false 26*1, 59*2, 28*3 5.313,3.052 6.823,3.458 1.51,0.406 10 false Certification ECU (Smart Key ECU Assembly) 2.99,3.042 5.438,3.24 2.448,0.198 10 false *2: for 2GR-FKS 3,3.333 5.292,3.531 2.292,0.198 10 false *3: for 2AR-FE 2.99,2.76 5.094,3.104 2.104,0.344 10 false *1: for A25A-FKS


w/ ID Code Box


B463090E11
0.667,3.063 1.125,3.26 0.458,0.198 10 false ECM 0.677,2.896 2.135,3.198 1.458,0.302 10 false A23*1, A22*2 5.292,2.896 5.75,3.094 0.458,0.198 10 false K139 5.979,0.24 6.438,0.438 0.458,0.198 10 false 12 V 1.125,1.375 1.583,1.573 0.458,0.198 10 false 12 V 5.292,0.969 5.75,1.167 0.458,0.198 10 false EFII 5.302,1.865 5.76,2.063 0.458,0.198 10 false EFIO 5.104,0.969 5.563,1.167 0.458,0.198 10 false 3 5.104,1.865 5.563,2.063 0.458,0.198 10 false 4 1.625,0.948 2.208,1.167 0.583,0.219 10 false IMO 1.688,1.865 2.146,2.063 0.458,0.198 10 false IMI 1.969,0.948 2.958,1.26 0.99,0.313 10 false 45 1.969,1.865 3.292,2.125 1.323,0.26 10 false 59*1, 28*2 5.292,3.063 6.865,3.458 1.573,0.396 10 false ID Code Box (Immobiliser Code ECU) 2.99,3.042 5.438,3.24 2.448,0.198 10 false *1: for 2GR-FKS 3,3.333 5.292,3.531 2.292,0.198 10 false *2: for 2AR-FE


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ECM, certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to Service Bulletin.

*1: w/o ID Code Box

*2: w/ ID Code Box


·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B279986 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Result Proceed to
NEXT (w/o ID Code Box) A
NEXT (w/ ID Code Box) B



A

2.CHECK ECM (TERMINAL EFII)

B

8.CHECK ECM (TERMINAL EFII)
2.CHECK ECM (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.

B473425C01
2.052,0.25 2.469,0.5 0.417,0.25 3.292,4.573 3.104,4.573 3.104,4.573 3.104,3.927 false 2.729,4.573 2.917,4.573 2.917,4.573 2.917,3.927 false 2.865,2.073 2.677,2.073 2.677,2.073 2.677,1.031 true 0.198,0.229 0.51,0.427 0.313,0.198 10 false *a 0.948,3.885 1.583,4.26 0.635,0.375 10 false GND 2.906,1.99 3.542,2.365 0.635,0.375 10 false EFII 2.958,2.99 3.271,3.188 0.313,0.198 10 false *b 2.583,4.479 2.896,4.677 0.313,0.198 10 false *c 3.323,4.49 3.635,4.688 0.313,0.198 10 false *d 2.125,0.292 2.76,0.667 0.635,0.375 10 false A13
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
A13-3 (EFII) - Body ground Engine switch on (IG) 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal EFII stuck low (2.4 V or less) B
Waveform not output, or has abnormal wavelength or shape C



A

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)

B

6.CHECK ECM

C

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B473424C02
2.042,0.25 2.458,0.5 0.417,0.25 3.021,4.594 3.208,4.594 3.208,4.594 3.208,4.073 false 3.573,4.594 3.385,4.594 3.385,4.594 3.385,4.073 false 2.781,2.125 2.594,2.125 2.594,2.125 2.594,1.063 true 0.104,0.271 0.417,0.427 0.313,0.156 10 false *a 3.26,3.042 3.573,3.198 0.313,0.156 10 false *b 2.885,4.5 3.198,4.656 0.313,0.156 10 false *c 3.594,4.5 3.906,4.656 0.313,0.156 10 false *d 2.115,0.292 2.427,0.448 0.313,0.156 10 false A13 0.896,4.021 1.49,4.302 0.594,0.281 10 false GND 2.833,2.031 3.427,2.313 0.594,0.281 10 false EFIO
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
A13-4 (EFIO) - Body ground Engine switch turned on (IG) using registered electrical key transmitter sub-assembly 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

4.REGISTER ECU COMMUNICATION ID

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER ENGINE STARTS
5.CHECK WHETHER ENGINE STARTS
a.

Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the engine switch on (IG).


b.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

NG

6.CHECK ECM
a.

Disconnect the A24*1, A23*2 or A22*3 ECM connector.

*1: for A25A-FKS

*2: for 2GR-FKS

*3: for 2AR-FE



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for A25A-FKS
Tester Connection Condition Specified Condition
A24-25 (IMO) - Body ground Engine switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform

for 2GR-FKS
Tester Connection Condition Specified Condition
A23-45 (IMO) - Body ground Engine switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform

for 2AR-FE
Tester Connection Condition Specified Condition
A22-45 (IMO) - Body ground Engine switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

B

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the A13 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for A25A-FKS
Tester Connection Condition Specified Condition
A13-3 (EFII) - A24-25 (IMO) Always Below 1 Ω
A13-3 (EFII) or A24-25 (IMO) - Other terminals and body ground Always 10 kΩ or higher

for 2GR-FKS
Tester Connection Condition Specified Condition
A13-3 (EFII) - A23-45 (IMO) Always Below 1 Ω
A13-3 (EFII) or A23-45 (IMO) - Other terminals and body ground Always 10 kΩ or higher

for 2AR-FE
Tester Connection Condition Specified Condition
A13-3 (EFII) - A22-45 (IMO) Always Below 1 Ω
A13-3 (EFII) or A22-45 (IMO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK ECM (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.

C379326C07
3.24,0.104 3.708,0.333 0.469,0.229 3.198,3.552 3.031,3.552 3.031,3.552 3.031,3.042 true 2.667,3.563 2.833,3.563 2.833,3.563 2.833,3.052 true 3.906,1.49 3.74,1.49 3.74,1.49 3.521,0.938 true 2.458,0.302 2.771,0.458 0.313,0.156 10 false *a 2.854,2.083 3.167,2.24 0.313,0.156 10 false *b 2.51,3.469 2.823,3.625 0.313,0.156 10 false *c 3.24,3.479 3.552,3.635 0.313,0.156 10 false *d 0.885,3 1.198,3.156 0.313,0.156 10 false GND 3.948,1.406 4.313,1.583 0.365,0.177 10 false EFII 3.313,0.135 4.021,0.573 0.708,0.438 10 false K139
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
K139-3 (EFII) - Body ground Engine switch on (IG) 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
Normal waveform A
Terminal IMO stuck low (2.4 V or less) B
Waveform not output, or has abnormal wavelength or shape C



A

9.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)

B

12.CHECK ECM

C

9.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

C379327C11
3.292,0.063 3.75,0.281 0.458,0.219 3.344,0.833 2.844,1.26 2.844,1.26 2.698,1.26 true 3.583,3.531 3.417,3.531 3.417,3.531 3.417,3.031 true 3.073,3.542 3.24,3.542 3.24,3.542 3.24,3.042 true 2.573,0.25 2.885,0.406 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.927,2.99 1.24,3.146 0.313,0.156 10 false GND 3.365,0.094 3.781,0.323 0.417,0.229 10 false K139 2.344,1.177 2.76,1.375 0.417,0.198 10 false EFIO
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
K139-4 (EFIO) - Body ground Engine switch turned on (IG) using registered electrical key transmitter sub-assembly 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

10.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

10.REGISTER ECU COMMUNICATION ID (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the engine switch on (IG).


b.

Check that the engine can be started 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID HAS NOT BEEN REGISTERED)

NG

12.CHECK ECM
a.

Disconnect the A23*1 or A22*2 ECM connector.

*1: for 2GR-FKS

*2: for 2AR-FE



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 2GR-FKS
Tester Connection Condition Specified Condition
A23-45 (IMO) - Body ground Engine switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform

for 2AR-FE
Tester Connection Condition Specified Condition
A22-45 (IMO) - Body ground Engine switch turned on (IG) using registered electrical key transmitter sub-assembly Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or abnormal waveform B



A

13.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

B

13.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the K139 ID code box (immobiliser code ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2GR-FKS
Tester Connection Condition Specified Condition
K139-3 (EFII) - A23-45 (IMO) Always Below 1 Ω
K139-3 (EFII) or A23-45 (IMO) - Other terminals and body ground Always 10 kΩ or higher

for 2AR-FE
Tester Connection Condition Specified Condition
K139-3 (EFII) - A22-45 (IMO) Always Below 1 Ω
K139-3 (EFII) or A22-45 (IMO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR