If the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2 is stuck high, the ECM will store this DTC.
*1: w/o ID Code Box
*2: w/ ID Code Box
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B279A | Theft Deterrent System Communication Line High Fixation | The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly)*2 or ID code box (immobiliser code ECU)*3 is stuck high. (1 trip detection logic*1) | ·
Certification ECU (smart key ECU assembly)*2 ·
ID code box (immobiliser code ECU)*3 ·
ECM ·
Wire harness or connector |
DTC output confirmation operation:
Turn the engine switch on (IG) and wait 6 seconds. |
| B279A12 | Engine Immobiliser System Circuit Short to Battery | The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly)*2 or ID code box (immobiliser code ECU)*3 is stuck high. (1 trip detection logic*1) | ·
Certification ECU (smart key ECU assembly)*2 ·
ID code box (immobiliser code ECU)*3 ·
ECM ·
Wire harness or connector |
DTC output confirmation operation:
Turn the engine switch on (IG) and wait 6 seconds. |
*1: Only output while a malfunction is present.
*2: w/o ID Code Box
*3: w/ ID Code Box
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | Engine cannot be started |
| DTC No. | Data List and Active Test |
|---|---|
| B279A*1
B279A12*2 |
- |
*1: for 2AR-FE
*2: except 2AR-FE
w/o ID Code Box
w/ ID Code Box
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the ECM, certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to Service Bulletin.
*1: w/o ID Code Box
*2: w/ ID Code Box
After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When DTC B279A*1 or B279A12*2 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.
*1: for 2AR-FE
*2: except 2AR-FE
Turn the engine switch off.
Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2.
*1: w/o ID Code Box
*2: w/ ID Code Box
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the engine starts.
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o ID Code Box) | B |
| NG (w/ ID Code Box) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-4 (EFIO) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
*b | Waveform |
| *c | Approximately 160 ms. | *d | Approximately 270 ms. |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| A13-4 (EFIO) - Body ground | Engine switch turned on (IG) using registered electrical key transmitter sub-assembly | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform) |
| Proceed to |
|---|
| OK |
| NG |
OK
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>ECM>REMOVAL
NG
Disconnect the A24*1, A23*2 or A22*3 ECM connector.
*1: for A25A-FKS
*2: for 2GR-FKS
*3: for 2AR-FE
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-4 (EFIO) - A24-26 (IMI) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-4 (EFIO) - A23-59 (IMI) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A13-4 (EFIO) - A22-28 (IMI) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for A25A-FKS: Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>ECM>REMOVAL
NG
| *a | Component with harness connected
(ID Code Box (Immobiliser Code ECU)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K139-4 (EFIO) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(ID Code Box (Immobiliser Code ECU)) |
*b | Waveform |
| *c | Approximately 160 ms. | *d | Approximately 270 ms. |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| K139-4 (EFIO) - Body ground | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform) |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>ECM>REMOVAL
NG
Disconnect the A23*1 or A22*2 ECM connector.
*1: for 2GR-FKS
*2: for 2AR-FE
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K139-4 (EFIO) - A23-59 (IMI) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K139-4 (EFIO) - A22-28 (IMI) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>ECM>REMOVAL
NG