If the certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more, DTC B2785 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2785 | Communication Malfunction between ECUs Connected by LIN | ·
Errors in LIN communication between ECUs or an open or short in communication lines. ·
The certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more. |
·
Certification ECU (smart key ECU assembly) ·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
ID code box (immobiliser code ECU)* ·
Wire harness or connector |
*: w/ ID Code Box
Before performing the inspection, check that DTC B2786 or B278C is not output.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU)* or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.
*: w/ ID Code Box
Disconnect the K62 certification ECU (smart key ECU assembly) connector.
Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the K139 ID code box (immobiliser code ECU) connector.*
*: w/ ID Code Box
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.*
*: w/ ID Code Box
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K62-13 (LIN) - K65-5 (LIN) | Ignition switch off | Below 1 Ω |
| K62-13 (LIN) - K139-2 (LIN) | Ignition switch off | Below 1 Ω |
| K62-13 (LIN), K65-5 (LIN) or K139-2 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K62-13 (LIN) - K65-5 (LIN) | Always | Below 1 Ω |
| K62-13 (LIN) or K65-5 (LIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the K62 certification ECU (smart key ECU assembly) connector.
Connect the K139 ID code box (immobiliser code ECU) connector.*
*: w/ ID Code Box
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC B2785 is output (w/o ID Code Box) | A |
| DTC B2785 is output (w/ ID Code Box) | B |
| DTC B2785 is not output | C |
A
B
C
for Manual Tilt and Manual Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY
for Power Tilt and Power Telescopic Steering Column: Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY
Connect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the K139 ID code box (immobiliser code ECU) connector.
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC B2785 is output | A |
| DTC B2785 is not output | B |
A
B